radio noise

[et]

I have a radio question. Glasair 1TD with Icom radio, older headset.
When the engine is running and charging 14.5 volts the radio howls
when I transmit. Engine off, battery voltage, no noise. If I put
a small screwdriver in the small hole in the headset and turn it down
1/2 turn, no noise. If I then take the headset and plug it in my old
Cherokee, it won't transmit until I turn it back up.

Are all headsets this voltage sensetive? Or just older ones? Is
there a fix?

thanks

Ed

[Orval Fairbairn[_2_]]

In article
>,
et > wrote:

> I have a radio question. Glasair 1TD with Icom radio, older headset.
> When the engine is running and charging 14.5 volts the radio howls
> when I transmit. Engine off, battery voltage, no noise. If I put
> a small screwdriver in the small hole in the headset and turn it down
> 1/2 turn, no noise. If I then take the headset and plug it in my old
> Cherokee, it won't transmit until I turn it back up.
>
> Are all headsets this voltage sensetive? Or just older ones? Is
> there a fix?
>
> thanks
>
> Ed

You need a capacitor between the alternator o/p and ground, to suppress
noise. All the aviation supply houses sell noise suppressors.

[et]

On Nov 26, 9:18*am, Orval Fairbairn >
wrote:
> In article
> >,
>
> *et > wrote:
> > I have a radio question. * Glasair 1TD with Icom radio, older headset..
> > When the engine is running and charging 14.5 volts the radio howls
> > when I transmit. * Engine off, battery voltage, no noise. * *If I put
> > a small screwdriver in the small hole in the headset and turn it down
> > 1/2 turn, no noise. * If I then take the headset and plug it in my old
> > Cherokee, it won't transmit until I turn it back up.
>
> > Are all headsets this voltage sensetive? * Or just older ones? *Is
> > there a fix?
>
> > thanks
>
> > Ed
>
> You need a capacitor between the alternator o/p and ground, to suppress
> noise. All the aviation supply houses sell noise suppressors.

It's not that kind of noise, it's a loud howl when I try to transmit,
receives great. It will also howl after I shut down the engine,
until the battery voltage drops a little, then it transmits great.
Never does it when receiving.

Ed

[[email protected]]

On Fri, 26 Nov 2010 11:41:37 -0800 (PST), et >
wrote:

>On Nov 26, 9:18Â*am, Orval Fairbairn >
>wrote:
>> In article
>> >,
>>
>> Â*et > wrote:
>> > I have a radio question. Â* Glasair 1TD with Icom radio, older headset.
>> > When the engine is running and charging 14.5 volts the radio howls
>> > when I transmit. Â* Engine off, battery voltage, no noise. Â* Â*If I put
>> > a small screwdriver in the small hole in the headset and turn it down
>> > 1/2 turn, no noise. Â* If I then take the headset and plug it in my old
>> > Cherokee, it won't transmit until I turn it back up.
>>
>> > Are all headsets this voltage sensetive? Â* Or just older ones? Â*Is
>> > there a fix?
>>
>> > thanks
>>
>> > Ed
>>
>> You need a capacitor between the alternator o/p and ground, to suppress
>> noise. All the aviation supply houses sell noise suppressors.
>
>It's not that kind of noise, it's a loud howl when I try to transmit,
>receives great. It will also howl after I shut down the engine,
>until the battery voltage drops a little, then it transmits great.
>Never does it when receiving.
>
>Ed
>
>
>
>
Lots of radios are sensitive to overvoltage. Try putting a diode or 2
in series with the power lead and see what happens. Most work just
fine as low as 10.5 volts or so - so even a good voltage regulator
(low dropout) could do the job - but I'd recommend a couple of silicon
rectifier diodes - minimum 24 volt and 50% more than the rated
current, better yet 50 volt and double the transmitter current.
>
>
>
>
>
>

[abripl[_3_]]

It could be the radio side tone feedback causing the noises. I had
noise in my radio(s) when transmitting so it was not alternator
related. I adjusted the radio side tone to almost nil and now no more
noises and perfect transmission. I know it's distracting not to hear
yourself but it solved the problem.

[Elvise]

here is some tips for How to Reduce Radio Interference on a Headset

1- Insert the headset's audio plug into the audio output of an audio device.
2- Remove the battery cover on the back of the noise canceling device. Insert fresh batteries into the battery compartment and close the cover.
3- Insert one end of a mini-jack audio cable into the audio output of the audio device
4- Insert always fresh batteries into the battery compartments and close the covers.