Flarm error

[glidergreg]

Anyone know what a FLARM error three is. I get this voice message on my Butterfly Vario then the flarm page goes to a large X.

[Dan Daly[_2_]]

On Friday, September 5, 2014 9:17:21 AM UTC-4, glidergreg wrote:
> Anyone know what a FLARM error three is. I get this voice message on my Butterfly Vario then the flarm page goes to a large X.

I don't know what that one is, but last weekend I was getting a "FLARM IO" error when trying to download to a USB stick. I tried other sticks, error-checking them, re-formatting them, with no luck. Also tried directly to the Core, vs the USB panel pass-through.

I then re-installed the flarmcfg.txt file, and that fixed the problem (both sticks can download). I also updated the flarmnet data in the Butterfly display.

I'd try redoing your flarmcfg.txt file as a starting point.

Dan
2D

[glidergreg]

On Friday, September 5, 2014 8:17:21 AM UTC-5, glidergreg wrote:
> Anyone know what a FLARM error three is. I get this voice message on my Butterfly Vario then the flarm page goes to a large X.

Thanks Dan,

I also found that when I download a newer updated version to my PC, it will add a (1) or(2) to the end of the flie name before the period. I assume that the PC knows that a file with a similar name exists and adds the (-) to differentiate it. To fix this I rename the file by removing any of the (-) in the name and then upload it to the device.

Anyone have a listing of what these FLAMR error codes are or imply?

[Dave Nadler]

On Friday, September 5, 2014 9:17:21 AM UTC-4, glidergreg wrote:
> Anyone know what a FLARM error three is.
> I get this voice message on my Butterfly Vario

What does the voice message say?

> then the flarm page goes to a large X.

From the dataport specification, there is no error
code 3. There is a SEVERITY 3, which means "fatal error".
That is accompanied with an error code describing
the problem in detail.

Your display device does not tell you the
actual error code?

Hope that helps,
Best Regards, Dave

[Eric]

I thought Powerflarm core could only download flights and upload
declarations via the USB port? Can you now do these via a tablet and
the serial port?

Basil


On Fri, 5 Sep 2014 08:00:57 -0700 (PDT), Dan Daly
> wrote:

>On Friday, September 5, 2014 9:17:21 AM UTC-4, glidergreg wrote:
>> Anyone know what a FLARM error three is. I get this voice message on my Butterfly Vario then the flarm page goes to a large X.
>
>I don't know what that one is, but last weekend I was getting a "FLARM IO" error when trying to download to a USB stick. I tried other sticks, error-checking them, re-formatting them, with no luck. Also tried directly to the Core, vs the USB panel pass-through.
>
>I then re-installed the flarmcfg.txt file, and that fixed the problem (both sticks can download). I also updated the flarmnet data in the Butterfly display.
>
>I'd try redoing your flarmcfg.txt file as a starting point.
>
>Dan
>2D

[jfitch]

On Friday, September 5, 2014 6:17:21 AM UTC-7, glidergreg wrote:
> Anyone know what a FLARM error three is. I get this voice message on my Butterfly Vario then the flarm page goes to a large X.

What version of firmware on the Butterfly Vario?

Later that 1.0.8 (build 2100 or so) the Vario seems to try to communicate with the PF anytime you download flight files. Something happens in the protocol and you will get the voice warning "FLARM ERROR 3" repeated every 30 seconds and all communication with the Flarm is lost until reboot.

With 1.0.8 I have not had that error. Later builds, happens every time. I have reported it to Air, but no resolution that I know of yet.