|
|
What happened to the Biplane Hangar? by
Skrud
A few years ago there was a clearinghouse for folks building Skybolts and
Pitts Model 12's called the Biplane Hangar. Is this e-mail exploder group
still active?
Scott
|
January 28th 06 12:35 PM
by Skrud
|
2 |
589 |
|
|
ISO Christen Air/Oil Separator by
Skrud
In search of a used, very good condition Christen aerobatic air oil
separator. Please e-mail me if you have one available.
Thanks,
Scott
|
May 13th 06 01:54 AM
by Skrud
|
0 |
1,060 |
|
|
Tools: Crappy Camloc Drill Jig by
Skrud
Purchased a MilSpec brand handheld drill jig for Camloc receptacles a few
weeks ago and used it for the first time today. What a piece of crap.
The "tool steel" bushing must not be hardened, as it wallowed out after 7
uses (14 holes). Junk, junk, junk. Going to have it hardness tested at...
|
|
4 |
925 |
|
|
FA: Gas Regulators by
Skrud
In case anyone's interested, I just listed my set of single-stage Smith
regulators (oxygen & acetylene) on eBay. Bought a set of two-stage units so
the old ones get to go.
Look for stuff being sold by scottrod.
Thanks!
|
August 21st 06 03:19 AM
by Skrud
|
0 |
541 |
|
|
Battery Contactor Diode? by
Skrud
What is the correct type of diode (p/n) to put across a garden-variety
battery contactor to prevent the inductive spike?
( 1 2 3)
|
|
25 |
4,138 |
|
|
Rattray Aero Status? by
Skrud
Anyone know the status of Rattray Fiberglass in Beloit, Wisconsin?
The phone's been "temporarily disconnected" according to the message...
Scott in Ohio
|
May 26th 07 10:36 PM
by Skrud
|
0 |
1,605 |
|
|
Alt. question by
sky bob
I am building a Long EZ and am the stage where I am ready to start the
engine installation and have a couple questions for the group. The
Alt. that I have is a small single wire 60 amp alt W/ a built in
regulator that I will be putting on a Lyc. 0-235 my quastions are as
follows. 1. Is there a way...
|
|
9 |
733 |
|
|
electric/electronic tach by
sky bob[_2_]
The project that I purchased (Long EZ) came with a electric tach and a
sender/sensor that attaches to the tach drive on the rear of the
engine. It is made by a Co. called Carr. I have been looking for the
manufacture on the web as I am in need of a different sender/sensor.
wondering if anyone has...
|
|
1 |
567 |
|
|
Sending units by
sky bob[_2_]
I have two new oil pressure sending units that came with the project
that I purchased. They look identical other than one has a single post
on top W/nut and the other has two posts. There is no instructions in
the boxes and the VDO gage is already installed . Is one better that
the other? Any...
|
|
1 |
699 |
|
|
Gage & sender by
sky bob[_2_]
I have a new never used UMA 2 1/4" suction gage Mod # 3-102-12 for
sale also a new in the box Westach fuel pressure send Mod #387-13st W/
instructions and wiring for sale. If interested please contact me off
group.
|
|
1 |
937 |
|
|
FOR SALE: GARMIN 295 Handheld GPS by
Sky King
FOR SALE: GARMIN 295 color GPS is in pristine condition. I am the sole
owner and bought it brand new. It has never been dropped and is in excellent
shape. Included are the latest GARMIN software upgrades. It has had very
little use. Also included are all the original GARMIN manuals,...
|
|
0 |
961 |
|
|
|
|
0 |
1,315 |
|
|
Sailplane wing joint by
Sky Surfer
Hi all,Â*
I started studying Jim Marske's Composite Design Manual to understand composite techniques generally and glider construction in particular.Â* My current topic of interest is the best design for joining two plug-in wings for a small sailplane, say in the 13 meter class.Â* It seems the...
|
|
6 |
7,437 |
|
|
Destination - Gathering of Eagles XII July 13-15 by
SkyDaddy
Shameless non-commercial plug: If you're in striking distance of
Cleveland the weekend of July 13-15, you're invited to drop in at
Willoughby Lost Nation (KLNN, east of Cleveland).
We'll have an interesting assortment of classics, warbirds, and
homebuilts, including Gerry Beck's "ultimate...
|
|
0 |
733 |
|
|
Wooden laminations by
SkyDaddy
About five years ago I cut and planed Douglas Fir planks for the
landing gear of my Fly Baby, but we moved before I got them glued up.
I'm finally getting back into the swing of things. Should I re-plane
them to get a fresh-cut surface before I glue them?
|
|
1 |
852 |
|
|
corrosion-proofing 4130 fittings by
SkyDaddy
Having perused the preserved wisdom of this board going back to 1997,
what's the best way to keep Mr. Rust from doing the nom-nom-nom on my
carefully-crafted 4130 fittings?
Thanks to my friendly neighborhood college-chem-lab person I can dip
them in phosphoric acid (with all appropriate safety...
|
|
1 |
585 |
|
|
Las Vegas Airsports? by
Skyking
I'm trying to contact these people and all I get
is a phone recording. They don't return calls.
Is there anyone out there who knows anything about them?
http://www.fly702.com/
Thanks, Skyking
|
November 25th 03 12:48 PM
by Skyking
|
0 |
690 |
|
|
Kingman, AZ Fly-IN by
Skyking
There will be a Pancake Breakfast Fly In at the Kingman, AZ EAA Hangar
tomorrow, May 15th.
It is the Hangar Opening celebration.
Skyking
|
|
3 |
868 |
|
|
RV-8 Instructor? by
Skyking
I have a friend in Kingman,AZ who needs some help with
landing his RV-8. Is there anyone near Kingman who could help?
The person would need access to a dual control RV-8 as
the time is not flown off of his airplane yet.
Thanks,
Skyking
|
|
8 |
739 |
|
|
Kingman,AZ Fly-IN/Pancake Breakfast by
Skyking
Join Kingman EAA Chapter 765
in Celebrating the Completion
of Our New Hangar at Our
4th. Annual Spring Fly-In
Saturday, May 15, 2004
7:30 am - 2 pm
Pancake Breakfast
7:30 am - 11:00 am
|
|
2 |
1,012 |