karel wrote: seeing the set of plans available on e-bay, i took a look on this aircraft and it looks like a possible alternative for the Europa. of course, some questions arise: -) are any flying in Europe? Pas encore, mais il y a plusieurs personnes qui pensent à cet avion

Hello, On an O200 nose, we can see four threaded holes 1/4-20. I have a bad copy of the drawing I read 1-7/8 from center line horizontaly and 1-5/8 from center line verticaly. Is it true? I can't read the pilot diameter? Is someone knows it?

Hello, On my Gardan Minicab F-PRAZ, I have a A65-8F. I have some question about these engines (only for experimental use) 1- Is the rear case fuel pump serviceable, or did I need a new rear case for new oil pump? 2-May I bolt any cylinder P/N on any crankcase? for exemple a C90 cylinder

Hello, about carbon fiber blades: what is the blades resistance of sand abrasion, rain and gravel impacts? Is carbon fiber leading edge acceptable? Is metalic leading edge mandatory? thanks

Hello, The Becker VHF has two mike input What is the difference between std mike input and dynamic one? May I connect an intercom either in one or the other VHF input?

Hello, With two ANR headsets, is a vox intercom still useful? Thanks -- Philippe Vessaire Ò¿Ó¬

Hello, ACS sold an afordable set for retrofit old headsets with ANR electronics. Does some one use this? Is it simple to fit in a David Clack H10-30? Same question for Pilot Avionics 10-40? Thanks --

Hello, What are the best corosion resistant cylinder for O200 engine? genuine TCM ECI-Titan Millennium Cylinders from Superior airparts. any other I don't know... Thanks

Hello, Is this engine is #1 or #2 dynafocal mount? Thanks -- Minicab F-PRAZ Philippe Vessaire Ò¿Ó¬

Hello, Any comment about this prop. Will I be happy with an O200 on my Minicab (110kts expected)? thanks -- Minicab F-PRAZ Philippe Vessaire Ò¿Ó¬

After the Empire by Emmanuel Todd, ISBN: 978-0231131032 -- Pub: http://www.slowfood.fr/france Philippe Vessaire Ò¿Ó¬

Hello, Is any body know the wiring for these ignition module? http://www.transpo.de/cgi-win/product.exe?DM1929 http://www.transpo.de/cgi-win/product.exe?DM1927 or SMP-LX345 and SMP-LX356 summit racing ref.

Hello, I have a straight fuel inlet (AN940 style). May I bolt a 90° fuel inlet (AN842 style)? Is it possible to use AN842 or do I need other parts numbers? Thanks -- Pub: http://www.slowfood.fr/france

Hello, who know the époxy resin and the foam use to built a vison? Happy new year -- Pub: http://www.slowfood.fr/france Philippe Vessaire Ò¿Ó¬

hello, what is the technology of a common sensor. Any simple electronic (resistor) part equivalent? Thanks -- Philippe Vessaire

Hello, Is someone know the component inside a carburator temp sensor? I find the Spruce prices (around $200) overpriced for a homebuilt. Thanks -- Philippe Vessaire Ò¿Ó¬

Hello, Many people know this permanent magnet alternator I read different things about the maxi current it may deliver. Spruce say 12A for the model 200G P/N 07-06575 I read 10A to 15A possible. My A65 drive it at 6000rpm (2000 rpm for the engine). What current may I expect from?

Hello, What about these prop? May I realy gain a little more airspeed versus ordinary prop? What gain with carbon fiber? My airplane: Gardan MiniCab, engine A65.

Hello, when I read 90,000 lb/sqi for strength, is it just before the part is broken or is it the elastic limit? Thanks -- Philippe Vessaire Ò¿Ó¬

Hello, Is anyone have comments about the plsar super cruiser (former kis)? I don't find any builder home page. Thanks -- true autopilot fly airbus Philippe Vessaire Ò¿Ó¬