I am tidying up my 172 and need some new elevator and rudder tip sets, and dorsal fairings pre giving it a paint job. Any good experiences? thanks, Rowntree

http://www.cnn.com/2006/US/03/20/branson.crash.ap/index.html

Where are the manufacturer numbers stamped on the cylinder?

ONLINE RESOURCE FOR HELP DESK SOFTWARE ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ http://helpdesksoftwaremanagement.blogspot.com

Anyone purchase one of these for their Cherokee? They tell me that removal of the existing panel is easy and the total job (including remounting the defroster ducts) will take no more than 2 hours. For the life of me, I cannot see how it can be that easy. The padded lip is mounted SOLIDLY to the...

I've ordered a pair of CI-291 Comant com antennas to replace the well worn antennas on my Archer. Besides removing any oxidation where the aluminum base contacts the aircraft and making sure the coax connector is clean and serviceable and the mechanical connection robust, are there other...

No matter what your argument is - it's "BUYER BEWARE" The plane I just bought recently was after driving to Atlanta, GA - Pensacola, FL - Meridian, MS - and then to two towns in Wisconsin. And that was starting from central Mississippi. I knew good and well when I left for each one that it may...

and back in the saddle, but not without a little excitement *smile*. 30 hours later, $1,700 less in my wallet and new wheel bearings to show for it, I decided to take a short hop from KMBO (Madison, MS) to KJAN (Jackson MS) which was a whole 9 NM to pick up a passenger who was coming in on...

On Fri, 10 Oct 2008 00:30:26 GMT, Mike wrote: "Gezellig" wrote in message ... On Wed, 08 Oct 2008 23:07:20 GMT, Mike wrote: So is everyone who flies VFR over the top or on a *moonless* night. Are all ...

I'm considering the purchase of a share in a Steen Skybolt (homebuilt biplane). I'd never seen one before and my mechanical experience consists of peeking under the cowl of rental aircraft (this would be my first airplane). Needless to say, I need somebody familiar with the type to have a...

That is what AmeriKA has become!

Are there any small airparks and flying clubs around the Phoenix AZ area? I'm not talking about the airports on the sectional chart. I'm looking for the small grass or dirt fields with Experimentals and or Ultralights? OK I suppose some may be on sectional charts. -- Have a good day and stay...

1974 Cessna 310Q - Colemill Excellent condition Details at: http://www.drainbrain.info/cessna/

In my continuing effort to plug all the oil leaks in my Continental 0-300 I have a final question about wet vacuum pumps. How much oil out the vent is too much? This is a '61 C-172 with the factory standard oil recovery system off the wet vac. About twice as much oil comes out the vacuum vent as...

There doesn't seem to be a lot of information available on the web (first time for everything) with regard to tie down space in SoCal (specifically SNA). What is the best way to go about this. I know there is a waiting list as long as my arm (or longer). But I've also been told that many people are...

Good day I'm looking to purchase a 60' Warp drive 2 blades propeller. It needs to be a pusher type in good condition, preferably square tip. Is there someone that has one for sale. If yes, would appreciate photo before purchasing. Thank you Jean-Paul Roy Angliers, Quebec

We´re looking for a second-hand pressurised twin-engine aircraft, to seat sixteen to nineteen passangers plus crew, such as a Raytheon Beechcraft 1900 -C or -D version or Jetstream 32, which has easy acess to spares and maintainance within the Florida state, as well as flight simmulators within the...

I just installed a Michel TKM MX 11r which is a direct slide-in replacement for my Narco 120 Comm. Because I have an intercom, I had to add a resistor to the circuit board. Having done this, I installed the radio in the old Narco tray and tested the radio: Findings: 1/ Comm works great with...

And it only took 15 months... ;-) When we bought Atlas (our '74 Cherokee 235 Pathfinder, named because he can lift ANYTHING we can fit inside) in 2002, the only thing I didn't like was his interior. We immediately replaced the ceiling plastic, but the rest of the interior was tired, too. A...

I'd like to find out more about this. Do you have a reference to an official article? "Roger Long" wrote in message ... Say, this really looks to be for real. AOPA just advised me not to stay ...