![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
I want (need) a new prop for my C152. Sensenich has a 12-week lead
time. Are there other sources? 2nd question: Anybody have any comments the Sparrow Hawk conversion? |
#2
|
|||
|
|||
![]()
Wag Aero has those props. I got one
about 5 years ago.. Hope you have good luck. It makes a difference. Bill OParowski |
#3
|
|||
|
|||
![]()
Paul Folbrecht wrote:
I want (need) a new prop for my C152. Sensenich has a 12-week lead time. Are there other sources? 2nd question: Anybody have any comments the Sparrow Hawk conversion? Paul, 1. http://www.propellerman.com/ although, they may be a bit "pre-occupied" today... 2. We converted our fleet of 152's years ago, and have been pleased with the results. Lower spark plugs stay cleaner, the revised baffling is more serviceable, and of course the performance improvement is welcome, if not dramatic. Only real drawback is that the piston rings tend to get "soft" at about 1500 hours, probably due to increased heat of cumbustion. A quick hone and new ring set cures that, and its off for another 1500 hours. Happy Flying! Scott Skylane N92054 |
#4
|
|||
|
|||
![]()
Another real drawback I learned of is the decrease of TBO from 2400 to
2000. But thanks. Scott Skylane wrote: Paul Folbrecht wrote: I want (need) a new prop for my C152. Sensenich has a 12-week lead time. Are there other sources? 2nd question: Anybody have any comments the Sparrow Hawk conversion? Paul, 1. http://www.propellerman.com/ although, they may be a bit "pre-occupied" today... 2. We converted our fleet of 152's years ago, and have been pleased with the results. Lower spark plugs stay cleaner, the revised baffling is more serviceable, and of course the performance improvement is welcome, if not dramatic. Only real drawback is that the piston rings tend to get "soft" at about 1500 hours, probably due to increased heat of cumbustion. A quick hone and new ring set cures that, and its off for another 1500 hours. Happy Flying! Scott Skylane N92054 |
#5
|
|||
|
|||
![]()
Paul Folbrecht wrote:
Another real drawback I learned of is the decrease of TBO from 2400 to 2000. But thanks. /snip/ Paul, Unless the airplane will be flying under part 135 or 121, the TBO figure is meaningless. We routinely flew our engines 3500-4000 hours between overhauls. This, of course, was only acheivable due to the high utilization rates (about 100 hours per month, year-round). Your mileage probably WILL vary, but I really don't think the Sparrowhawk conversion has any meaningul effect on the engines life, other than the prior mentioned ring issue. Remember, to get the 2400 hour "TBO" on a regular O-235 L2C, you must use a specific heavy piston part number, as well as "100% Genuine Lycoming Parts" throughout the rest of the engine. Install even one aftermarket valve cover gasket, and *poof*, the "TBO" magically drops back to 2000 hours. As I said, meaningless... Happy Flying! Scott Skylane N92054 |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
A Remote Compass- java source | [email protected] | General Aviation | 0 | July 3rd 04 06:39 PM |
4130 sheet source | Leon McAtee | Home Built | 7 | May 2nd 04 08:29 PM |
Warp drive or other ground adjustable props | Wallace Berry | Home Built | 0 | March 10th 04 04:02 PM |
Props and Wing Warping... was soaring vs. flaping | Wright1902Glider | Home Built | 0 | September 29th 03 03:40 PM |
Source for copper crush gaskets??? | Jim | Home Built | 2 | August 22nd 03 09:44 PM |