|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
December 21st 16, 12:48 AM
posted to rec.aviation.soaring
|
|||
|
|||
Flarm/ClearNav Help Needed
Hi All,
I built a cable for My Power FLARM portable according to the drawing on the Tech Tips portion of the ClearNav site but The CN does not connect to the Flarm. I have a cable tester and the cable checks good. I've tried baud rates from 19.2 to 57.6K and still no luck. I also spoke with another CNII user at Moriarty and he asked me if I'd enabled FLARM on my CNII. I've looked and can't find anything other than Flarm Status - There is none, and Flarm Alerts and I have the longest alerts selected. What about the Flarm dataport strings? Flarm Only or Flarm and Nav (I've tried it both ways without success)? Does anyone have any other suggestions? -- Dan, 5J 
|
|
#2
December 21st 16, 01:25 AM
posted to rec.aviation.soaring
|
|||
|
|||
|
Flarm/ClearNav Help Needed
On Tuesday, December 20, 2016 at 7:48:11 PM UTC-5, Dan Marotta wrote:
Hi All, I built a cable for My Power FLARM portable according to the drawing on the Tech Tips portion of the ClearNav site but The CN does not connect to the Flarm. I have a cable tester and the cable checks good. I've tried baud rates from 19.2 to 57.6K and still no luck. I also spoke with another CNII user at Moriarty and he asked me if I'd enabled FLARM on my CNII. I've looked and can't find anything other than Flarm Status - There is none, and Flarm Alerts and I have the longest alerts selected. What about the Flarm dataport strings? Flarm Only or Flarm and Nav (I've tried it both ways without success)? Does anyone have any other suggestions? -- Dan, 5J Power Flarm has to finish power up dance before you start CN. Ryszard
|
|
#3
December 21st 16, 01:49 AM
posted to rec.aviation.soaring
|
|||
|
|||
|
Flarm/ClearNav Help Needed
On Tuesday, December 20, 2016 at 5:25:16 PM UTC-8, RW wrote:
On Tuesday, December 20, 2016 at 7:48:11 PM UTC-5, Dan Marotta wrote: Hi All, I built a cable for My Power FLARM portable according to the drawing on the Tech Tips portion of the ClearNav site but The CN does not connect to the Flarm. I have a cable tester and the cable checks good. I've tried baud rates from 19.2 to 57.6K and still no luck. I also spoke with another CNII user at Moriarty and he asked me if I'd enabled FLARM on my CNII. I've looked and can't find anything other than Flarm Status - There is none, and Flarm Alerts and I have the longest alerts selected. What about the Flarm dataport strings? Flarm Only or Flarm and Nav (I've tried it both ways without success)? Does anyone have any other suggestions? -- Dan, 5J Power Flarm has to finish power up dance before you start CN. Ryszard Also the higher the baud rate, the longer the connection process. The CN2 starts looking at low rates then goes higher. Jim
|
|
#4
December 21st 16, 03:44 AM
posted to rec.aviation.soaring
|
|||
|
|||
|
Flarm/ClearNav Help Needed
Dan -- pls check the forum.
Thx Evan
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| trying to work out how you connect the flarm view 57 to mini box flarm running a V7 and Oudie | Michael Marshall[_2_] | Soaring | 3 | April 10th 16 04:13 AM |
| trying to work out how you connect the flarm view 57 to mini box flarm running a V7 and Oudie | Michael Marshall[_2_] | Soaring | 0 | April 8th 16 08:57 PM |
| Information for all users of Flarm, OEM FLARM supplier and Flarm PowerFlarm | [email protected] | Soaring | 28 | March 12th 16 04:31 AM |
| Integrating Flarm with Clearnav | [email protected] | Soaring | 8 | September 6th 12 01:33 PM |
| Help needed: ILEC SN10 pilots with FLARM | Dave Nadler | Soaring | 2 | December 1st 09 12:03 AM |
Linear Mode
