A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Owning
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Maintenance questions



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old August 12th 05, 03:03 AM
JJS
external usenet poster
 
Posts: n/a
Default Maintenance questions

Okay, the Cherokee 140 annual is nearly finished. Compressions are 80, 80, 80, & 78 over 80 after 5 1/2 years and
650 hours of mostly autogas use.

So far everything looks very good except for two things. My A&P IA was inspecting the propeller spinner back plate
and was turning the prop real slow by hand as he did so. He noticed that the impulse coupler on the left mag wasn't
clicking. He turned it a little faster and it works fine. Tried it slow again and sometimes... no clicky. Since
I've had no starting problems, he suggests I just keep flying it unless it begins to give trouble. The mags won't be
due for overhaul for at least another year. My question is: Is there a slow death type "normal" failure mode in
which progressively harder starts occur or do impulse couplers usually fail suddenly and leave you stranded? I
really don't want to throw away money. On the other hand I'd rather not get stranded after dark at an airport away
from home with no mechanics around or parts to be had.

Question #2 The nose strut is not leaking, but there is a spot in which the chrome plating is beginning to blister.
It is hard to see and is low on the strut where it would take some extremely hard braking or a big bump, (or one of
my not so good landings, come to think of it) to get the top portion of the strut to pass over it. Eventually I
suspect, it will need attention. Is it still possible to have these struts rechromed? A Google search turned up a
post from 2002 listing these guys:

Industrial Plating Co. Inc.
1300 Clydesdale Avenue
P.O. Drawer 2365
Anniston, AL 36201
800-525-6408
Fax 256-237-1579

FAA Repair Station # IPBR525K

Can anyone who has had this done in the not to distant past recommend additional business possibilities and perhaps
relate a cost to do it?


--
Joe Schneider
8437R
(Remove No Spam to Reply)



----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Homebuilt Aircraft Frequently Asked Questions List (FAQ) Ron Wanttaja Home Built 40 October 3rd 08 03:13 PM
Homebuilt Aircraft Frequently Asked Questions List (FAQ) Ron Wanttaja Home Built 0 December 2nd 04 07:00 AM
Homebuilt Aircraft Frequently Asked Questions (FAQ) Ron Wanttaja Home Built 0 October 1st 04 02:31 PM
Homebuilt Aircraft Frequently Asked Questions List (FAQ) Ron Wanttaja Home Built 0 September 2nd 04 05:15 AM
Homebuilt Aircraft Frequently Asked Questions (FAQ) Ron Wanttaja Home Built 0 June 2nd 04 07:17 AM


All times are GMT +1. The time now is 07:40 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AviationBanter.
The comments are property of their posters.