|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
November 14th 07, 06:08 PM
posted to rec.aviation.homebuilt
|
|||
|
|||
Hole template or Drawing for Altimeter
I am looking for a drawing for the instrument panel hole for a 3 1/8
altimeter. Thanks in advance. Richard www.craggyaero.com 
|
|
#2
November 14th 07, 06:42 PM
posted to rec.aviation.homebuilt
|
|||
|
|||
|
Hole template or Drawing for Altimeter
Craggy Aero wrote:
I am looking for a drawing for the instrument panel hole for a 3 1/8 altimeter. Thanks in advance. Richard www.craggyaero.com I'm pretty sure there is one in the ACS catalog and it is available online in .pdf format.
|
|
#3
November 15th 07, 12:40 AM
posted to rec.aviation.homebuilt
|
|||
|
|||
|
Hole template or Drawing for Altimeter
If you want to do it the hard way (like I always like to do!), you can
just cut out a 3-1/8" hole (if it's a 3-18" altimeter) and file the notch very slowly to fit the adjusting knob... Scott Gig 601XL Builder wrote: Craggy Aero wrote: I am looking for a drawing for the instrument panel hole for a 3 1/8 altimeter. Thanks in advance. Richard www.craggyaero.com I'm pretty sure there is one in the ACS catalog and it is available online in .pdf format. -- Scott http://corbenflyer.tripod.com/ Gotta Fly or Gonna Die Building RV-4 (Super Slow Build Version)
|
|
#4
November 15th 07, 03:21 PM
posted to rec.aviation.homebuilt
|
|||
|
|||
|
Hole template or Drawing for Altimeter
I had it. Please sent me an Email. I will give it to you.
My Email: Luo http://www.ming-da.com Craggy Aero $BLF;!'(B I am looking for a drawing for the instrument panel hole for a 3 1/8 altimeter. Thanks in advance. Richard www.craggyaero.com
|
|
#5
November 15th 07, 03:38 PM
posted to rec.aviation.homebuilt
|
|||
|
|||
|
Hole template or Drawing for Altimeter
I had sent it into your Email. Please check it.
Luo http://ww.ming-da.com Craggy Aero $BLF;!'(B I am looking for a drawing for the instrument panel hole for a 3 1/8 altimeter. Thanks in advance. Richard www.craggyaero.com
|
|
#6
November 15th 07, 03:40 PM
posted to rec.aviation.homebuilt
|
|||
|
|||
|
Hole template or Drawing for Altimeter
I had sent it into your Email.
Luo ŽÊ“¹F I had it. Please sent me an Email. I will give it to you. My Email: Luo http://www.ming-da.com Craggy Aero $BLF;!'(B I am looking for a drawing for the instrument panel hole for a 3 1/8 altimeter. Thanks in advance. Richard www.craggyaero.com
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Worm Hole no Need for Black Hole | Michael Baldwin, Bruce | Products | 2 | May 8th 07 12:04 PM |
| Airpath C2400 compass correction card template ? | [email protected] | Soaring | 4 | March 9th 07 07:55 PM |
| 3 1/8" instrument template | [email protected] | Home Built | 4 | April 15th 06 03:26 AM |
| LS3 flaperon gap seal template needed | Birdbones | Soaring | 2 | May 14th 05 01:46 AM |
| Looking for a good "offer to purchase" sample/ template | Bob | Owning | 0 | September 26th 04 09:57 PM |
Linear Mode
