![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
A year ago I began having audio problems. I would only get the up
sound at 4+. Sometimes, toward the end of the flight, I didn't even get sound at 5+. The instrument itself tracks the same as the Winter, and the averager works ( as confirmed by another pilot in the air.). Additionally, after an hour in the air, the Borgelt ceased issuing a sound when I flew too fast. (Occasionally it would still emit the appropriate sound, but there were long periods of silence when I was flying fast at a low McR. setting.) The associated instrument did indicate that I was flying too fast. At this point I sent it back to the factory and paid $200. They said that there was nothing wrong with the instrument and suggested that I may not know how to operate it. After using it successfully for 4 years, that seemed like an odd suggestion. Now I have a new problem. Sometimes when I find lift, the audio is correct. Other times it indicates a rapidly increasing lift (13+ ave. and rising) when the lift is 3 or less. Has anyone else experienced this problem? Does anyone have any suggestions for solving the problem other than up-grading? |
#2
|
|||
|
|||
![]()
On Jan 2, 10:26 am, Vsoars wrote:
A year ago I began having audio problems. I would only get the up sound at 4+. Sometimes, toward the end of the flight, I didn't even get sound at 5+. The instrument itself tracks the same as the Winter, and the averager works ( as confirmed by another pilot in the air.). Additionally, after an hour in the air, the Borgelt ceased issuing a sound when I flew too fast. (Occasionally it would still emit the appropriate sound, but there were long periods of silence when I was flying fast at a low McR. setting.) The associated instrument did indicate that I was flying too fast. At this point I sent it back to the factory and paid $200. They said that there was nothing wrong with the instrument and suggested that I may not know how to operate it. After using it successfully for 4 years, that seemed like an odd suggestion. Now I have a new problem. Sometimes when I find lift, the audio is correct. Other times it indicates a rapidly increasing lift (13+ ave. and rising) when the lift is 3 or less. Has anyone else experienced this problem? Does anyone have any suggestions for solving the problem other than up-grading? Two thoughts: 1. Check your wiring for the speaker. It is usually external to the unit and could be a weak spot in your system. 2. Check that your voltages are all good. Mine does odd things when the voltage starts to drop. 3. There is a know problem with the switching from run to climb mode that will cause some errors. This requires a new resistor, but that should have been checked if it went back to the factory. Sorry you are having problems, it seems odd that you would get that response from Borgelt, I have always had good service so far with my B50. |
#3
|
|||
|
|||
![]()
I has similar problems with my B-40.......................then I found
a loose speaker wire going into the back of the unit. JJ |
#4
|
|||
|
|||
![]() "Vsoars" wrote in message ... A year ago I began having audio problems. I would only get the up sound at 4+. Sometimes, toward the end of the flight, I didn't even get sound at 5+. The instrument itself tracks the same as the Winter, and the averager works ( as confirmed by another pilot in the air.). Additionally, after an hour in the air, the Borgelt ceased issuing a sound when I flew too fast. (Occasionally it would still emit the appropriate sound, but there were long periods of silence when I was flying fast at a low McR. setting.) The associated instrument did indicate that I was flying too fast. At this point I sent it back to the factory and paid $200. They said that there was nothing wrong with the instrument and suggested that I may not know how to operate it. After using it successfully for 4 years, that seemed like an odd suggestion. Now I have a new problem. Sometimes when I find lift, the audio is correct. Other times it indicates a rapidly increasing lift (13+ ave. and rising) when the lift is 3 or less. Has anyone else experienced this problem? Does anyone have any suggestions for solving the problem other than up-grading? Yes, it came back here last Easter and we checked it. This involves disassembly, careful checking of the solder joints on the boards, reassembly and a functional check running for several hours on the bench. If it still works OK (and I couldn't get that unit to miss a beat on our test rig), I heat the things up to +50 deg C and check again and again at -20 deg C after a cold soak in the freezer. I couldn't get that unit to fail as I notified the owner at the time before sending it back. Yes we charge for our time when checking out of warranty instruments. The charge was A$100(about US$80 or so at the time I think). This compares rather favorably with what our local TV/hifi repair shop charges. The fault description was somewhat incomprehensible without clarification which lead me to believe that there was something wrong with the cruise/climb switching or that the owner didn't properly understand the logic behind how the the audio is meant to work. This has happened before. A loose speaker wire or faulty speaker or loose cruise climb switch wire can also cause odd symptoms which of course won't be present on the instrument when we test it. It is possible there is a bad component in that B50. If it can be got to fail consistently or even fail on my bench we can fix it. We do, however, charge for out of warranty repairs and shipping is paid for by the owner. It would also help if we were notified that the problem was still present or that other symptoms were now occurring. I find the statement: "Sometimes when I find lift, the audio is correct. Other times it indicates a rapidly increasing lift (13+ ave. and rising) when the lift is 3 or less." less than clear. Does this mean the averager now reads 13 knots sometimes when it should read 3 knots? And the audio follows this? What is the vario indication doing? I don't know. I do know a large percentage of problems are in the installation in the glider which is why we ask you to contact us so we can discuss the problem and run a few simple checks to eliminate these. Like the club with a two seater recently who weren't getting good total energy for the year they had had the new glider. After being contacted recently I discussed the problem with the guy trying to fix it and eventually I asked him to leak check the line(which should have been done on installation originally). Turns out the TE probe was plugged in to a triple probe fitting with the spare unused tubes open in the cockpit. Mike Borgelt |
#5
|
|||
|
|||
![]()
On Wed, 02 Jan 2008 09:26:24 -0800, Vsoars wrote:
A year ago I began having audio problems. I would only get the up sound at 4+. Sometimes, toward the end of the flight, I didn't even get sound at 5+. The instrument itself tracks the same as the Winter, and the averager works ( as confirmed by another pilot in the air.). Additionally, after an hour in the air, the Borgelt ceased issuing a sound when I flew too fast. (Occasionally it would still emit the appropriate sound, but there were long periods of silence when I was flying fast at a low McR. setting.) The associated instrument did indicate that I was flying too fast. At this point I sent it back to the factory and paid $200. They said that there was nothing wrong with the instrument and suggested that I may not know how to operate it. After using it successfully for 4 years, that seemed like an odd suggestion. Now I have a new problem. Sometimes when I find lift, the audio is correct. Other times it indicates a rapidly increasing lift (13+ ave. and rising) when the lift is 3 or less. Has anyone else experienced this problem? Does anyone have any suggestions for solving the problem other than up-grading? The instrument has been checked on the bench and no problems were found, but the symptoms persist. Obviously the fault lies in the glider. First thing to check is the battery. Is the battery also 4 years old? Does the problem get worse when you press the ptt switch on the radio? Batteries fail in an unpredictable manner and the voltage might be healthy on the ground before and recover soon after flight, but fade to the point where things stop working when you need them most during flight. Try swap the battery and see if it helps. Then have a look at the battery wiring, plugs, fuses, switches etc. Also look at speaker wiring and the speaker itself. (I have noticed our B500 do similar weird things - when the battery voltage gets down to 9.5V.) Ian |
#6
|
|||
|
|||
![]()
While we are on the subject of wiring, check that the instrument is
wired with power all the way back to the positive and ground buss strips (you do have them don't you?). Ground loops can cause all sorts of weirdness in electronic equipment. In other words, each instrument should be wired, _both_ power and ground, independently to a common point - usually some sort of buss arrangement. What can happen if you, for instance, connect the power wire from each instrument back to a "positive" buss but connect the ground from the vario to the adjacent radio housing which is in turn grounded to the ground buss through its own wiring, is that a portion of the current (signal?) from one of the instruments will actually be routed through another instrument... That is rarely good. So, be sure that each instrument is wired (both positive and ground wires!!!!) back to the busses. Larry "the REAL cable guy" Goddard "Ian" wrote in message : On Wed, 02 Jan 2008 09:26:24 -0800, Vsoars wrote: A year ago I began having audio problems. I would only get the up sound at 4+. Sometimes, toward the end of the flight, I didn't even get sound at 5+. The instrument itself tracks the same as the Winter, and the averager works ( as confirmed by another pilot in the air.). Additionally, after an hour in the air, the Borgelt ceased issuing a sound when I flew too fast. (Occasionally it would still emit the appropriate sound, but there were long periods of silence when I was flying fast at a low McR. setting.) The associated instrument did indicate that I was flying too fast. At this point I sent it back to the factory and paid $200. They said that there was nothing wrong with the instrument and suggested that I may not know how to operate it. After using it successfully for 4 years, that seemed like an odd suggestion. Now I have a new problem. Sometimes when I find lift, the audio is correct. Other times it indicates a rapidly increasing lift (13+ ave. and rising) when the lift is 3 or less. Has anyone else experienced this problem? Does anyone have any suggestions for solving the problem other than up-grading? The instrument has been checked on the bench and no problems were found, but the symptoms persist. Obviously the fault lies in the glider. First thing to check is the battery. Is the battery also 4 years old? Does the problem get worse when you press the ptt switch on the radio? Batteries fail in an unpredictable manner and the voltage might be healthy on the ground before and recover soon after flight, but fade to the point where things stop working when you need them most during flight. Try swap the battery and see if it helps. Then have a look at the battery wiring, plugs, fuses, switches etc. Also look at speaker wiring and the speaker itself. (I have noticed our B500 do similar weird things - when the battery voltage gets down to 9.5V.) Ian |
#7
|
|||
|
|||
![]()
On Jan 3, 4:03 pm, "01-- Zero One" wrote:
While we are on the subject of wiring, check that the instrument is wired with power all the way back to the positive and ground buss strips (you do have them don't you?). Ground loops can cause all sorts of weirdness in electronic equipment. In other words, each instrument should be wired, _both_ power and ground, independently to a common point - usually some sort of buss arrangement. What can happen if you, for instance, connect the power wire from each instrument back to a "positive" buss but connect the ground from the vario to the adjacent radio housing which is in turn grounded to the ground buss through its own wiring, is that a portion of the current (signal?) from one of the instruments will actually be routed through another instrument... That is rarely good. So, be sure that each instrument is wired (both positive and ground wires!!!!) back to the busses. Larry "the REAL cable guy" Goddard "Ian" wrote in message : On Wed, 02 Jan 2008 09:26:24 -0800, Vsoars wrote: A year ago I began having audio problems. I would only get the up sound at 4+. Sometimes, toward the end of the flight, I didn't even get sound at 5+. The instrument itself tracks the same as the Winter, and the averager works ( as confirmed by another pilot in the air.). Additionally, after an hour in the air, the Borgelt ceased issuing a sound when I flew too fast. (Occasionally it would still emit the appropriate sound, but there were long periods of silence when I was flying fast at a low McR. setting.) The associated instrument did indicate that I was flying too fast. At this point I sent it back to the factory and paid $200. They said that there was nothing wrong with the instrument and suggested that I may not know how to operate it. After using it successfully for 4 years, that seemed like an odd suggestion. Now I have a new problem. Sometimes when I find lift, the audio is correct. Other times it indicates a rapidly increasing lift (13+ ave. and rising) when the lift is 3 or less. Has anyone else experienced this problem? Does anyone have any suggestions for solving the problem other than up-grading? The instrument has been checked on the bench and no problems were found, but the symptoms persist. Obviously the fault lies in the glider. First thing to check is the battery. Is the battery also 4 years old? Does the problem get worse when you press the ptt switch on the radio? Batteries fail in an unpredictable manner and the voltage might be healthy on the ground before and recover soon after flight, but fade to the point where things stop working when you need them most during flight. Try swap the battery and see if it helps. Then have a look at the battery wiring, plugs, fuses, switches etc. Also look at speaker wiring and the speaker itself. (I have noticed our B500 do similar weird things - when the battery voltage gets down to 9.5V.) Ian- Hide quoted text - - Show quoted text - I have flown over 600 hours with the Borgelt, using it at contests, record and Diamond flights. My partner in this glider is an electrical engineer. I came to this group to get specific suggestions since returning the instrument to the manufacturer didn't work. And several people have given us some excellent ideas. Thanks for those of you who provided suggestions. The manufacturer chose to enter the dialog. As he had said in earlier communication, Borgelt suggests that,"the owner didn't properly understand the logic behind how the audio is meant to work." That was not helpful. It rarely is helpful to place the blame on the consumer, especially one who has so much experience using all of the features of this instrument. I doubt if any of you would have liked to get this type of public response. If I had wanted a kick in the shin, I would have directly corresponded with Mike Borgelt. The B50 worked for most of the 600 hours. Because I use one battery to power the radio and the Volkslogger, I switch between two batteries; both produce the problem. One is less than a year old; the other just over a year in use. I have never had a flight tract rejected by OLC or the NAA, indicating that the power supply is adequate. This instrument was installed at the factory. It didn't work correctly, so we re-did the tubing. Finally we sent it back to the factory and they replaced the malfunctioning component. Whether it came from the factory with the defect, or the problem occurred before it was delivered here, I have no way of knowing. After that initial problem, I had no problems till recently. When an audio instrument starts screaming and the averager continues to climb till I shut off the power while the Winter shows 3 up, then one conclude that there is a problem, likewise the intermittent non- responding audio when I exceed the speed to fly. I checked and discovered that we purchased the B50 in 2001. Maybe that is the life of this particular instrument. I hope that is not the case (All my other instruments are years older.) I still hold out hope that some of the suggestions will provide a solution. I'm requesting that Borgelt limit his responses to a direct email to me. Otherwise, I'd appreciate anyone's ideas. |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Audio Circuit | Ken Gage | Home Built | 12 | May 21st 07 10:41 PM |
Need audio for my Vario's | jb92563 | Soaring | 2 | December 21st 05 04:26 AM |
RST-565 Audio Panel | Jim Weir | Owning | 0 | October 29th 04 08:57 PM |
Aux. Audio Input | Eugene Wendland | Home Built | 1 | April 5th 04 04:16 AM |
S-TEC 60-2 audio warning | Julian Scarfe | Owning | 7 | March 1st 04 08:11 PM |