![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
I'm selling off some of my "stock" of spare parts that don't fit my
Cherokee. I inherited most of them from an airport "old timer" years ago, and they've been sitting around ever since. I thought I'd give some of the newsgroup people a chance to make an offer before I Ebay them. I'll be investigating the worth of these items, so don't low ball "too" much. ![]() Buyers will also be responsible for paying shipping cost. I'll except a certified/bank check or PayPal (although I've never actually used my PayPal account, so I don't know how to use it). Nothing will be shipped until I have the money in my pocket. One Cherokee rams horn yoke and shaft for the larger diameter installations. If I don't get a reasonable price for this, I'll keep it for possible upgrade of my Cherokee. http://www2.ari.net/jmasino/private/yoke.JPG The rear section of a dorsal fin. Appears to be brand new. No holes have been drilled, except for the ones for the built-in captive nuts. Probably fits Warriors, Archers, later Arrows, etc. The rear is marked with part number 99619-02 http://www2.ari.net/jmasino/private/rear_dorsal.JPG Rear spinner backplate. I believe this is probably off of a Warrior 151. It's marked with part number 587-330. It's also marked $119, but that's probably a 15 year old price. http://www2.ari.net/jmasino/private/..._backplate.JPG Used wingtips for a hershey bar Cherokee. Removed from a 67 140 for Metco upgrade. Will probably fit other Cherokee models, too. http://www2.ari.net/jmasino/private/wingtips.JPG Overhead vent "tube" with mounting tray, louvered vents and control cable. Probably fits mid-70s Warriors. http://www2.ari.net/jmasino/private/overhead_vent.JPG Full carb heat shroud (top and bottom). I believe this is for a mid-70s Warrior. The top is marked with part number 99568-003, Rev M. The bottom is marked with part numbers 35302-3F and 35303-003, Rev D. Not sure which part number is the correct one on the bottom. http://www2.ari.net/jmasino/private/...at_shroud1.JPG http://www2.ari.net/jmasino/private/...at_shroud2.JPG Mufflers that I believe came off my old buddy's 73 Cherokee 180. They look like they have very little time on them. No visible cracks or deterioration of the baffles. http://www2.ari.net/jmasino/private/mufflers1.JPG http://www2.ari.net/jmasino/private/mufflers2.JPG -- __!__ Jay and Teresa Masino ___(_)___ http://www2.ari.net/jmasino ! ! ! http://www.oceancityairport.com http://www.oc-adolfos.com |
#2
|
|||
|
|||
![]()
The rear section of a dorsal fin. Appears to be brand new. No holes have
been drilled, except for the ones for the built-in captive nuts. Probably fits Warriors, Archers, later Arrows, etc. The rear is marked with part number 99619-02 http://www2.ari.net/jmasino/private/rear_dorsal.JPG Hmmmm. I wonder if this fits my '74 Pathfinder? (It sure *looks* the same...) Mine is cracking badly, and we decided to replace it at the next annual. Any idea how I can track down that part number? (I'm heading off to Reno in about 10 hours, so I prolly won't be around to answer. But if you can't sell it, set it aside for me and I'll catch you when I get back...) -- Jay Honeck Iowa City, IA Pathfinder N56993 www.AlexisParkInn.com "Your Aviation Destination" |
#3
|
|||
|
|||
![]()
In article YSM1d.178387$9d6.81094@attbi_s54, "Jay Honeck"
wrote: The rear section of a dorsal fin. Appears to be brand new. No holes have been drilled, except for the ones for the built-in captive nuts. Probably fits Warriors, Archers, later Arrows, etc. The rear is marked with part number 99619-02 http://www2.ari.net/jmasino/private/rear_dorsal.JPG Hmmmm. I wonder if this fits my '74 Pathfinder? (It sure *looks* the same...) Mine is cracking badly, and we decided to replace it at the next annual. Any idea how I can track down that part number? (I'm heading off to Reno in about 10 hours, so I prolly won't be around to answer. But if you can't sell it, set it aside for me and I'll catch you when I get back...) my (out-of-date?) parts list shows 99619-02 to be applicable (among others) to pa-28-235 with serial numbers 28-721001 and up. -- Bob Noel Seen on Kerry's campaign airplane: "the real deal" oh yeah baby. |
#4
|
|||
|
|||
![]()
Bob Noel wrote in message ...
In article YSM1d.178387$9d6.81094@attbi_s54, "Jay Honeck" wrote: The rear section of a dorsal fin. Appears to be brand new. No holes have been drilled, except for the ones for the built-in captive nuts. Probably fits Warriors, Archers, later Arrows, etc. The rear is marked with part number 99619-02 http://www2.ari.net/jmasino/private/rear_dorsal.JPG Hmmmm. I wonder if this fits my '74 Pathfinder? (It sure *looks* the same...) Mine is cracking badly, and we decided to replace it at the next annual. Any idea how I can track down that part number? (I'm heading off to Reno in about 10 hours, so I prolly won't be around to answer. But if you can't sell it, set it aside for me and I'll catch you when I get back...) my (out-of-date?) parts list shows 99619-02 to be applicable (among others) to pa-28-235 with serial numbers 28-721001 and up. N-number : N56993 Aircraft Serial Number : 28-7410040 Aircraft Manufacturer : PIPER Model : PA-28-235 Engine Manufacturer : LYCOMING Model : O&VO-360 SER Aircraft Year : 1973 Owner Name : INNOVATIVE DISTRIBUTION SYSTEMS INC Owner Address : 203 FRIENDSHIP ST IOWA CITY, IA, 52245-3914 Type of Owner : Corporation Registration Date : 18-Apr-2002 Airworthiness Certificate Type : Standard Approved Operations : Normal Looks like the part number qualifies for Jay's plane. |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
FA: Piper J3 Cub Parts | BFC | Aviation Marketplace | 0 | September 24th 04 03:20 PM |
FS: several Piper parts (long) | Jay Masino | Aviation Marketplace | 0 | September 15th 04 01:09 AM |
Source of Piper Parts | Mike Noel | Owning | 2 | June 25th 04 09:04 PM |
Piper cub J3 parts needed | Mathieu Dewavrin | Home Built | 0 | May 8th 04 09:33 AM |
The Piper Cubs That Weren't | Veeduber | Home Built | 5 | August 28th 03 04:38 AM |