![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
One of the fellows I fly with is building an RV-3 with an O-320-H2AD
Lycoming. He has searched the Web for an answer but didn't know about Usenet till now. His question concerns the mechanical fuel pump. It is located on the front of that series of engine. Has anyone runs fuel lines under the engine to the front without vapor lock issues? Or does anyone skip the mechanical pump and install 2 electric pumps? Has anyone run the fuel lines on the top side of the engine even it may be a fire hazard? D. |
#2
|
|||
|
|||
![]()
In article ,
"Capt.Doug" wrote: One of the fellows I fly with is building an RV-3 with an O-320-H2AD Lycoming. He has searched the Web for an answer but didn't know about Usenet till now. His question concerns the mechanical fuel pump. It is located on the front of that series of engine. Has anyone runs fuel lines under the engine to the front without vapor lock issues? Or does anyone skip the mechanical pump and install 2 electric pumps? Has anyone run the fuel lines on the top side of the engine even it may be a fire hazard? D. Why would that be any more of a fire hazard than running the fuel line under the engine? I would think that running the line in the cooler air than near such things as exhaust pipes, etc. |
#3
|
|||
|
|||
![]()
"Orval Fairbairn" wrote in message
Why would that be any more of a fire hazard than running the fuel line under the engine? I would think that running the line in the cooler air than near such things as exhaust pipes, etc. A&P Mechanic General Handbook states that fuel lines should be routed under engines and wire bundles in case the lines start to leak fuel. D. |
#4
|
|||
|
|||
![]() Quote:
to be honest, I am worried I hope someone could help me, I just have bought a H2AD for my low-wing plane. So, I decided to buy a fuel pump p/n LW-15399 from my part catalog Lyc_pc-122.pdf. After buy it from spruce, I had a big suprise at installation time, because I cant see nothing to move the arm of my fuel pump, I just see a hole whithout the camshaft extension to move the fuel pump. I cant see installation details in the catalog and I am worried about it. Any help will be very grateful. Regards. Helio ps: please see what I see in my O320-H2AD fuel pump location, and tell me understand why that: http://www.ppxdf.com/h2ad/image_1.jpg http://www.ppxdf.com/h2ad/image_2.jpg http://www.ppxdf.com/h2ad/image_3.jpg http://www.ppxdf.com/h2ad/image_4.jpg http://www.ppxdf.com/h2ad/image_5.jpg http://www.ppxdf.com/h2ad/image_6.jpg |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Lyc. O-360 cylinder question | JB | Owning | 13 | November 27th 04 09:32 PM |
Handheld battery question | RobsSanta | General Aviation | 8 | September 19th 04 03:07 PM |
A question on Airworthiness Inspection | Dave S | Home Built | 1 | August 10th 04 05:07 AM |
Question | Charles S | Home Built | 4 | April 5th 04 09:10 PM |
Partnership Question | Harry Gordon | Owning | 4 | August 16th 03 11:23 PM |