![]()  | 
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. | 
		
			
  | 	
	
	
		
		|||||||
| 
		 | 
	Thread Tools | Display Modes | 
| 
		 
			 
			#1  
			 
            
			
			
			
		 
		
		
	 | 
|||
		
		
  | 
|||
| 
	
	
		
			
			 
I have a 1962 cessna 172 that I am doing the interior in and I can not 
		
	
		
		
		
		
		
	
		 
		
	
	
	figure out how the door handles come off. I thought thy would have a standard "U" clip like cars, but these have a small spring that I can see behind there. Is there someway to push in and turn to unlock these things? Brad  | 
| 
		 
			 
			#2  
			 
            
			
			
			
		 
		
		
	 | 
|||
		
		
  | 
|||
| 
	
	
		
			
			 
I have a 1962 cessna 172 that I am doing the interior in and I can not 
		
	
		
		
		
		
		
	
		 
		
	
	
	figure out how the door handles come off. I thought thy would have a standard "U" clip like cars, My manual for 1973 Cessna M Shows the c\clip  | 
| 
		 
			 
			#3  
			 
            
			
			
			
		 
		
		
	 | 
|||
		
		
  | 
|||
| 
	
	
		
			
			 "Brad Mallard" wrote in message ... I have a 1962 cessna 172 that I am doing the interior in and I can not figure out how the door handles come off. I thought thy would have a standard "U" clip like cars, but these have a small spring that I can see behind there. Is there someway to push in and turn to unlock these things? Brad It's gotta be a clip. I took them off a 57 and 66 172 lately. Use the same flat tool used on cars and push the clip off from the open end.  | 
| 
		 
			 
			#4  
			 
            
			
			
			
		 
		
		
	 | 
|||
		
		
  | 
|||
| 
	
	
		
			
			 
Make sure you get that signed off by an A&P.... 
		
	
		
		
		
		
		
	
		 
		
	
	
	"Brad Mallard" wrote in message ... I have a 1962 cessna 172 that I am doing the interior in and I can not figure out how the door handles come off. I thought thy would have a standard "U" clip like cars, but these have a small spring that I can see behind there. Is there someway to push in and turn to unlock these things? Brad  | 
| Thread Tools | |
| Display Modes | |
		
  | 
	
		
  | 
			 
			Similar Threads
		 | 
	||||
| Thread | Thread Starter | Forum | Replies | Last Post | 
| VOR/DME Approach Question | Chip Jones | Instrument Flight Rules | 47 | August 29th 04 06:03 AM | 
| A question on Airworthiness Inspection | Dave S | Home Built | 1 | August 10th 04 06:07 AM | 
| 172 Repair question | Brad Mallard | Home Built | 2 | June 11th 04 03:54 AM | 
| Tecumseh Engine Mounting Question | jlauer | Home Built | 7 | November 16th 03 02:51 AM | 
| Question about Question 4488 | [email protected] | Instrument Flight Rules | 3 | October 27th 03 02:26 AM |