|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
April 5th 14, 08:01 PM
posted to rec.aviation.soaring
|
|||
|
|||
Butterfly display software - new version?
I was doing software updates on a new Brick/Core and Butterfly, and noticed the new Butterfly firmware version is 3.3. No changelog or manual yet. http://www.powerflarm.aero/index.php...ge-and-support .
PowerFLARM Core firmware is 3.4. 2D 
|
|
#2
April 6th 14, 04:22 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Butterfly display software - new version?
On Saturday, April 5, 2014 3:01:01 PM UTC-4, Dan Daly wrote:
I was doing software updates on a new Brick/Core and Butterfly, and noticed the new Butterfly firmware version is 3.3. No changelog or manual yet. http://www.powerflarm.aero/index.php...ge-and-support . 2D I just updated my Butterfly display and the big red butterfly is there on the boot screen, but it's a big black butterfly on the "no contact" screen. Can't see any other changes. 2D
|
|
#3
May 16th 14, 11:34 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Butterfly display software - new version?
On Saturday, April 5, 2014 1:01:01 PM UTC-6, Dan Daly wrote:
I was doing software updates on a new Brick/Core and Butterfly, and noticed the new Butterfly firmware version is 3.3. No changelog or manual yet. http://www.powerflarm.aero/index.php...ge-and-support . PowerFLARM Core firmware is 3.4. 2D Just updated Flarm Core, Butterfly display and Flarmnet today. I also noticed that the Butterfly display shows Version 3.3 on boot-up, despite loading Version 3.4 on the Core. CG
|
|
#4
May 17th 14, 03:28 AM
posted to rec.aviation.soaring
|
|||
|
|||
|
Butterfly display software - new version?
On Friday, May 16, 2014 3:34:34 PM UTC-7, wrote:
On Saturday, April 5, 2014 1:01:01 PM UTC-6, Dan Daly wrote: I was doing software updates on a new Brick/Core and Butterfly, and noticed the new Butterfly firmware version is 3.3. No changelog or manual yet. http://www.powerflarm.aero/index.php...ge-and-support . PowerFLARM Core firmware is 3.4. 2D Just updated Flarm Core, Butterfly display and Flarmnet today. I also noticed that the Butterfly display shows Version 3.3 on boot-up, despite loading Version 3.4 on the Core. CG Butterfly Display Software is Ver 3.3_2348 PowerFlarm Firmware 3.4 Richard www.craggyaero.com.
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| New Butterfly Display Software 3.2 | Marc - Butterfly Avionics | Soaring | 36 | March 8th 15 08:16 PM |
| FS: Flarm Butterfly 57mm Display $150 | joesimmers[_2_] | Soaring | 0 | February 24th 14 01:27 PM |
| New Butterfly Display Software 3.2.1 released | Marc - Butterfly Avionics | Soaring | 27 | August 28th 13 02:11 PM |
| Flarm Butterfly display | [email protected] | Soaring | 10 | May 6th 13 05:40 PM |
| Updating Software on Butterfly 57 mm version 2.1 display w/o Cable? | 3Y | Soaring | 7 | December 31st 12 12:50 PM |
Linear Mode
