A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Soaring
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Spray insulation for aluminum trailers



 
 
Thread Tools Display Modes
  #1  
Old July 20th 18, 08:14 PM posted to rec.aviation.soaring
[email protected]
external usenet poster
 
Posts: 266
Default Spray insulation for aluminum trailers

How does one go about having insulation installed inside an aluminum trailer?
Are there specific spray-on materials that are commonly applied that auto repair/painting shops would know how to work with? Are there some specific materials one should avoid? Seems like the material needs to be fairly abrasion resistant. Is the outgassing of some materials potentially damaging to a glider?

All the glued on carpet in my trailer is falling off for the second time and I do not look forward to redoing it all when a spray insulation may do double duty as padding for the glider bits and pieces.
  #2  
Old July 20th 18, 11:44 PM posted to rec.aviation.soaring
[email protected]
external usenet poster
 
Posts: 190
Default Spray insulation for aluminum trailers

Spray foam may add considerable weight to the top and over-burden the lifting mechanisms. Proceed with caution.

  #3  
Old July 22nd 18, 03:18 AM posted to rec.aviation.soaring
[email protected]
external usenet poster
 
Posts: 266
Default Spray insulation for aluminum trailers

That's it! That is all this forum has to offer on the subject of applying spray insulation to an aluminum top trailer. After all the discussion of Aluminum vs fiberglass?
I guess that implies that not a single person on this forum has any real world knowledge about insulating an aluminum top trailer?

  #4  
Old July 23rd 18, 07:17 PM posted to rec.aviation.soaring
[email protected]
external usenet poster
 
Posts: 266
Default Spray insulation for aluminum trailers

Thank you.
This is the first concrete suggestion/example of a method and materials to insulate the aluminum top.
  #5  
Old July 23rd 18, 08:51 PM
POPS POPS is offline
Member
 
First recorded activity by AviationBanter: Dec 2010
Posts: 76
Default

Quote:
Originally Posted by View Post
How does one go about having insulation installed inside an aluminum trailer?
Are there specific spray-on materials that are commonly applied that auto repair/painting shops would know how to work with? Are there some specific materials one should avoid? Seems like the material needs to be fairly abrasion resistant. Is the outgassing of some materials potentially damaging to a glider?

All the glued on carpet in my trailer is falling off for the second time and I do not look forward to redoing it all when a spray insulation may do double duty as padding for the glider bits and pieces.
Well.... I didn't use spray foam because of the permanence of it and once you pull the trigger you are not going to be able to clean up the potential of a horrific mess.
I did however line the entire interior with 3/4" cut and fit, foil lined foam boards.
Foil was positioned in the 'up' position, pushing back at, and stopping the UV from entering the trailer and touching anything in the interior. The surface temps are way way down now. Interior temp meets the ambient air temps of course, but not much more. The little mouse I found kick'n it recently would probably agree too. Very inexpensive, it was a day job, and if the next guy can't deal with the WTF fit and finish of it all .... remove it all in a few hours.
Started out as an experiment, turned into another permanent work-around/jury-rig. Did I mention cheeeeeeap ...
  #6  
Old July 23rd 18, 11:37 PM posted to rec.aviation.soaring
Nick Kennedy
external usenet poster
 
Posts: 124
Default Spray insulation for aluminum trailers

You may want to contact a local home insulating company that handles spray foam.
Its difficult to get it smooth thou in my experience. Google different types of spray foam and see what you find, good luck!

  #7  
Old July 24th 18, 01:37 AM posted to rec.aviation.soaring
George Haeh
external usenet poster
 
Posts: 257
Default Spray insulation for aluminum trailers

Rigid foam panels are available at any home improvement store. The trick will be finding a double sided tape tolerant of temperature extremes - or use a construction adhesive.

Be very careful of clearances, especially by the trailing edges of the wings.
  #8  
Old July 25th 18, 10:06 PM posted to rec.aviation.soaring
Eric Greenwell[_4_]
external usenet poster
 
Posts: 1,939
Default Spray insulation for aluminum trailers

POPS wrote on 7/23/2018 12:51 PM:

Well.... I didn't use spray foam because of the permanence of it and
once you pull the trigger you are not going to be able to clean up the
potential of a horrific mess.
I did however line the entire interior with 3/4" cut and fit, foil lined
foam boards.
Foil was positioned in the 'up' position, pushing back at, and stopping
the UV from entering the trailer and touching anything in the interior.
The surface temps are way way down now. Interior temp meets the ambient
air temps of course, but not much more. The little mouse I found kick'n
it recently would probably agree too. Very inexpensive, it was a day
job, and if the next guy can't deal with the WTF fit and finish of it
all .... remove it all in a few hours.
Started out as an experiment, turned into another permanent
work-around/jury-rig. Did I mention cheeeeeeap ...


How did you attach the foam panels to the aluminum top?

--
Eric Greenwell - Washington State, USA (change ".netto" to ".us" to email me)
- "A Guide to Self-Launching Sailplane Operation"
https://sites.google.com/site/motorg...ad-the-guide-1
- "Transponders in Sailplanes - Dec 2014a" also ADS-B, PCAS, Flarm

http://soaringsafety.org/prevention/...anes-2014A.pdf
  #9  
Old July 26th 18, 06:58 AM
POPS POPS is offline
Member
 
First recorded activity by AviationBanter: Dec 2010
Posts: 76
Default

Quote:
Originally Posted by Eric Greenwell[_4_] View Post
POPS wrote on 7/23/2018 12:51 PM:

Well.... I didn't use spray foam because of the permanence of it and
once you pull the trigger you are not going to be able to clean up the
potential of a horrific mess.
I did however line the entire interior with 3/4" cut and fit, foil lined
foam boards.
Foil was positioned in the 'up' position, pushing back at, and stopping
the UV from entering the trailer and touching anything in the interior.
The surface temps are way way down now. Interior temp meets the ambient
air temps of course, but not much more. The little mouse I found kick'n
it recently would probably agree too. Very inexpensive, it was a day
job, and if the next guy can't deal with the WTF fit and finish of it
all .... remove it all in a few hours.
Started out as an experiment, turned into another permanent
work-around/jury-rig. Did I mention cheeeeeeap ...


How did you attach the foam panels to the aluminum top?

--
Eric Greenwell - Washington State, USA (change ".netto" to ".us" to email me)
- "A Guide to Self-Launching Sailplane Operation"
https://sites.google.com/site/motorg...ad-the-guide-1
- "Transponders in Sailplanes - Dec 2014a" also ADS-B, PCAS, Flarm

http://soaringsafety.org/prevention/...anes-2014A.pdf


This style: Attached with hot glue. Why hot glue? So the next guy can peel it off and roll off the glue with pressure from a rubber door stopper, if he's a Felix type and can't handle the look of things.
Just trim the hangers pins for the flush fit/finish with the capture push on caps.

https://www.soundproofcow.com/produc...IaAonTEALw_wcB
  #10  
Old August 6th 18, 09:24 PM posted to rec.aviation.soaring
Eric Greenwell[_4_]
external usenet poster
 
Posts: 1,939
Default Spray insulation for aluminum trailers

POPS wrote on 7/25/2018 10:58 PM:


How did you attach the foam panels to the aluminum top?

--
Eric Greenwell - Washington State, USA (change ".netto" to ".us" to
email me)
- "A Guide


This style: Attached with hot glue. Why hot glue? So the next guy can
peel it off and roll off the glue with pressure from a rubber door
stopper, if he's a Felix type and can't handle the look of things.
Just trim the hangers pins for the flush fit/finish with the capture
push on caps.

http://tinyurl.com/y78sg8gx


Good idea! I didn't know there was such a thing.


--
Eric Greenwell - Washington State, USA (change ".netto" to ".us" to email me)
- "A Guide to Self-Launching Sailplane Operation"
https://sites.google.com/site/motorg...ad-the-guide-1
- "Transponders in Sailplanes - Dec 2014a" also ADS-B, PCAS, Flarm

http://soaringsafety.org/prevention/...anes-2014A.pdf
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Applying insulation to Aluminum Cobra trailer [email protected] Soaring 0 July 14th 18 04:54 AM
Used Destination Trailers for Sale | Portland | Als Trailers [email protected] Soaring 3 January 21st 18 05:43 AM
Break out the spray planes c-47 - File 2 of 2 - C-47 Spray 2.jpg (1/1) john Szalay Aviation Photos 0 August 8th 16 02:40 PM
Break out the spray planes Iwo Jima - File 1 of 4 - C-47 spray 1.jpg (1/1) john Szalay Aviation Photos 0 August 8th 16 02:39 PM
Aluminum top Cobra trailers leaks - how frequent? AK Soaring 2 March 31st 10 11:05 PM


All times are GMT +1. The time now is 11:54 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AviationBanter.
The comments are property of their posters.