If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Safety and Hot Wire Foam Cutting
A friend of mine just bought a hot wire foam cutting tool for carving
and shaping polystyrene foam. My question is whether the fumes and smoke from doing such carving are a safety/health hazard? Any guidelines for using such a tool safely? Thanks. -Fleemo |
#2
|
|||
|
|||
wrote in message ups.com... A friend of mine just bought a hot wire foam cutting tool for carving and shaping polystyrene foam. My question is whether the fumes and smoke from doing such carving are a safety/health hazard? Any guidelines for using such a tool safely? Thanks. -Fleemo My question is whether the fumes and smoke from doing such carving are a safety/health hazard? YES! (Duh) Any guidelines for using such a tool safely? Don't snort the fumes. Don't touch the hot parts. You're welcome. |
#3
|
|||
|
|||
"MikeR" wrote in message ... wrote in message ups.com... A friend of mine just bought a hot wire foam cutting tool for carving and shaping polystyrene foam. My question is whether the fumes and smoke from doing such carving are a safety/health hazard? Any guidelines for using such a tool safely? Thanks. -Fleemo My question is whether the fumes and smoke from doing such carving are a safety/health hazard? YES! (Duh) Any guidelines for using such a tool safely? Don't snort the fumes. Don't touch the hot parts. You're welcome. Welcome to Usenet, Fleemo! Minus the 'tude, he is about right. I haven't seen or heard anything about using a respirator to cut foam. Of course, they used to not worry about asbestos either. If you are worried, use a respirator. You might as well own a good one if you are going to be serious about building planes. |
#4
|
|||
|
|||
Where can I find a hot wire cutting tool? Thanks ahead.
Jean-Paul "Dude" wrote in message ... "MikeR" wrote in message ... wrote in message ups.com... A friend of mine just bought a hot wire foam cutting tool for carving and shaping polystyrene foam. My question is whether the fumes and smoke from doing such carving are a safety/health hazard? Any guidelines for using such a tool safely? Thanks. -Fleemo My question is whether the fumes and smoke from doing such carving are a safety/health hazard? YES! (Duh) Any guidelines for using such a tool safely? Don't snort the fumes. Don't touch the hot parts. You're welcome. Welcome to Usenet, Fleemo! Minus the 'tude, he is about right. I haven't seen or heard anything about using a respirator to cut foam. Of course, they used to not worry about asbestos either. If you are worried, use a respirator. You might as well own a good one if you are going to be serious about building planes. |
#5
|
|||
|
|||
Welcome to Usenet, Fleemo!
Thanks Dude, I appreciate the welcome. Minus the 'tude, he is about right. I haven't seen or heard anything about using a respirator to cut foam. Of course, they used to not worry about asbestos either. If you are worried, use a respirator. You might as well own a good one if you are going to be serious about building planes. I realize polysterene smoke is probably not something you want to breathe in like the bouquet of a fine wine, but I was looking for input on specifically how toxic it is and what steps need to be taken when carving foam with a hot wire. Is working in a well-ventilated room enough of a safety precaution, or is a respirator required? Where can I find a hot wire cutting tool? Jean-Paul, check out http://www.HotWireFoamFactory.com -Fleemo |
#6
|
|||
|
|||
Hi,
Your best bet is to get a MSDS on the product you intend on hot cutting. The product maker will send you one if you ask for it, and alot of them can be viewed on different companies websites. The sheet will tell you what kinds of protection you need, and what dangerous chemicals are involved, the dangers of the product and will even tell you if your children will be born with a arm sticking out of their forehead. Read the MSDS! Just for safety sake, always wear a respirator when doing anything like that. Make sure it is a proper respirator, remember a mask to keep wood dust out of your lungs will not keep chemicals out! Make sure you have good ventilation, and a fresh air system would be really nice. Patrick student SPL aircraft structural mech |
#7
|
|||
|
|||
"W P Dixon" wrote Just for safety sake, always wear a respirator when doing anything like that. Make sure it is a proper respirator, remember a mask to keep wood dust out of your lungs will not keep chemicals out! Make sure you have good ventilation, and a fresh air system would be really nice. Patrick Unless you can show evidence to contradict this, I say phooey! Fresh air system? You gotta be kidding! OP, work in a well ventilated area. Set up with a fan behind you, blowing the fumes away from you. If you see smoke rising, don't stick your nose in it. Nuff said. -- Jim in NC |
#8
|
|||
|
|||
wrote in message oups.com... Welcome to Usenet, Fleemo! Thanks Dude, I appreciate the welcome. Minus the 'tude, he is about right. I haven't seen or heard anything about using a respirator to cut foam. Of course, they used to not worry about asbestos either. If you are worried, use a respirator. You might as well own a good one if you are going to be serious about building planes. I realize polysterene smoke is probably not something you want to breathe in like the bouquet of a fine wine, but I was looking for input on specifically how toxic it is and what steps need to be taken when carving foam with a hot wire. Is working in a well-ventilated room enough of a safety precaution, or is a respirator required? Where can I find a hot wire cutting tool? Jean-Paul, check out http://www.HotWireFoamFactory.com -Fleemo Anyone telling you its safe is walking on thin ice. No one really knows, do they? I would not worry about it if I was going to build a plane or two. If I were going to do it for a living, I would wear protection. |
#9
|
|||
|
|||
Dude wrote:
wrote in message oups.com... Welcome to Usenet, Fleemo! Thanks Dude, I appreciate the welcome. Minus the 'tude, he is about right. I haven't seen or heard anything about using a respirator to cut foam. Of course, they used to not worry about asbestos either. If you are worried, use a respirator. You might as well own a good one if you are going to be serious about building planes. I realize polysterene smoke is probably not something you want to breathe in like the bouquet of a fine wine, but I was looking for input on specifically how toxic it is and what steps need to be taken when carving foam with a hot wire. Is working in a well-ventilated room enough of a safety precaution, or is a respirator required? Where can I find a hot wire cutting tool? Jean-Paul, check out http://www.HotWireFoamFactory.com -Fleemo Anyone telling you its safe is walking on thin ice. No one really knows, do they? I would not worry about it if I was going to build a plane or two. If I were going to do it for a living, I would wear protection. Good ventilation helps too. Dan, U.S. Air Force, retired |
#10
|
|||
|
|||
wrote in message
oups.com... I realize polysterene smoke is probably not something you want to breathe in like the bouquet of a fine wine, but I was looking for input on specifically how toxic it is and what steps need to be taken when carving foam with a hot wire. Is working in a well-ventilated room enough of a safety precaution, or is a respirator required? There is foam - and then there is foam. Polystyrene foam smoke ain't bad, but polyurethane foam smoke will give you a dirt nap. Go to http://www.info-central.org/construction_hotwire.shtml for a good primer on building a cutter and using it. Most modelers build their own cutter for a couple of bucks and use a 12 volt power supply. Even a battery charger will work. Rich S. |
|
Thread Tools | |
Display Modes | |
|
|