A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Home Built
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

homemade EFIS system and EMI



 
 
Thread Tools Display Modes
  #1  
Old January 25th 05, 08:06 PM
jcpearce
external usenet poster
 
Posts: n/a
Default homemade EFIS system and EMI

As a pet/learning project I made a data aquisition unit using an 8051
microprocessor and an EPIA M motherboard running a variant of Linux to
process and display the information. It all works but the EMI from the
EPIA M causes way too much noise to the aircraft radios. I have tried
shielding the whole device in an aluminum case with very little
improvement.

Any ideas on how to smother the EMI or some other small motherboard
which may not have as much an issue (as a test I took my portable
aviation radio and within 6' of any my home computers the same occurs
which gives me little hope)

Thanks

  #2  
Old January 25th 05, 09:30 PM
Peter
external usenet poster
 
Posts: n/a
Default

As a pet/learning project I made a data aquisition unit using an 8051
microprocessor and an EPIA M motherboard running a variant of Linux to
process and display the information. It all works but the EMI from the
EPIA M causes way too much noise to the aircraft radios. I have tried
shielding the whole device in an aluminum case with very little
improvement.

Any ideas on how to smother the EMI or some other small motherboard
which may not have as much an issue (as a test I took my portable
aviation radio and within 6' of any my home computers the same occurs
which gives me little hope)


Physically separate the offender from the victim, especially the point of
entry of the signals into the victim. Don't forget about coax cables, comm
antenna and things like that, not just the radio box. You could try
reorienting the motherboard 90 degrees in various axis.


  #3  
Old January 25th 05, 11:36 PM
jcpearce
external usenet poster
 
Posts: n/a
Default

This is without the system connected to any of the sensors, just
turning it on and with an external battery so it is physically isolated
but within 6' or so it causes interference. Rotating the motherboard
does not help either. Thanks for the reply.

  #4  
Old January 25th 05, 11:57 PM
Blueskies
external usenet poster
 
Posts: n/a
Default


"jcpearce" wrote in message oups.com...
This is without the system connected to any of the sensors, just
turning it on and with an external battery so it is physically isolated
but within 6' or so it causes interference. Rotating the motherboard
does not help either. Thanks for the reply.


I have the same problems with my desktop machine and handheld radio...Wrap with aluminum foil and see what happens...


  #5  
Old January 26th 05, 02:23 AM
UltraJohn
external usenet poster
 
Posts: n/a
Default

jcpearce wrote:

This is without the system connected to any of the sensors, just
turning it on and with an external battery so it is physically

isolatedseparateithin 6' or so it causes interference. Rotating the
motherboard
does not help either. Thanks for the reply.


Possibly try remotely mounting it back in the fusilage and running
fiberoptic to it. You can get inexpensive hobby FO and FO to rs232 modules
designed for experimenting.
Other than that try a non-aluminum case and use feed thru caps on all leads
and ferrite beads also. try some additional filtering on the PS and/or try
using separate PS for processor.
Just some thoughts.
John

ps those hobby aluminum cases do lousy for rfi prevention!

  #6  
Old January 26th 05, 05:14 AM
kumaros
external usenet poster
 
Posts: n/a
Default

jcpearce wrote:
As a pet/learning project I made a data aquisition unit using an 8051
microprocessor and an EPIA M motherboard running a variant of Linux to
process and display the information. It all works but the EMI from the
EPIA M causes way too much noise to the aircraft radios. I have tried
shielding the whole device in an aluminum case with very little
improvement.

Any ideas on how to smother the EMI or some other small motherboard
which may not have as much an issue (as a test I took my portable
aviation radio and within 6' of any my home computers the same occurs
which gives me little hope)

Thanks

You obviously are knowledgeable in the
subject, but have you tried the simple
stuff first, like ferrite doughnuts on
all cables to and from the boards and
grounding one side of cable shielding etc.?
It sounds like a very interesting
project, do you have a site for more info?
Kumaros
It's all Greek to me
  #7  
Old January 26th 05, 01:12 PM
Bob
external usenet poster
 
Posts: n/a
Default

The "noise" could be coming through the connector and could be emitting
from the wires.

Try using a connector with a metal housing and backshell and wires with
shields, terminate the shields to the connector backshell/housing which
will ground to the chassis.

The other end of the wires, try to terminate their shields where they
connect to.

Aircraft environment is not the same as home environment. Different
applications different techniques.

jcpearce wrote:
As a pet/learning project I made a data aquisition unit using an 8051
microprocessor and an EPIA M motherboard running a variant of Linux

to
process and display the information. It all works but the EMI from

the
EPIA M causes way too much noise to the aircraft radios. I have tried
shielding the whole device in an aluminum case with very little
improvement.

Any ideas on how to smother the EMI or some other small motherboard
which may not have as much an issue (as a test I took my portable
aviation radio and within 6' of any my home computers the same occurs
which gives me little hope)

Thanks


  #8  
Old January 26th 05, 03:44 PM
jcpearce
external usenet poster
 
Posts: n/a
Default

Thanks for the suggestions, no I have not posted what I did anywhere
but I think I will as it took me a little while to learn rudimentary
assembly, come up with a variant of linux running off flash memory,
write the code to process the serial output and display etc..

I did not use a hobby aluminum case, I custom built one with no gaps
(motherboard has a temperature sensor so I could check this for
possible overheating) and this was grounded. Without hooking up the
data aquisition card and just powering up the EPIA M in the seperate
aluminum case with no connections of any kind to the airplane I get the
interference in the radio. There are no connections coming out of the
aluminum box except for power and this line has caps on it for
filtering.

So it is coming solely from the motherboard, some chip on the board is
oscillating in the 107~130 Mhz range, given this occurs against one
home computer running at 2Ghz, another at 2.4 Ghz and the EPIA and 500
Mhz I would guess it is some supporting chip, but even if I knew I am
not sure that would do me much good. Perhaps changing the aluminum case
to a different size/shape would catch the offending frequency but I am
in the dark here and would be shooting in the dark.

There only seems two generic routes,
A) find a small computer which does not emit these frequencies (but I
do not know what is emmiting them so I would not know which computer
choice would alleviate this)
B) Some vastly better shielding approach for the motherboard.

Ideas?

Thanks



Bob wrote:
The "noise" could be coming through the connector and could be

emitting
from the wires.

Try using a connector with a metal housing and backshell and wires

with
shields, terminate the shields to the connector backshell/housing

which
will ground to the chassis.

The other end of the wires, try to terminate their shields where they
connect to.

Aircraft environment is not the same as home environment. Different
applications different techniques.

jcpearce wrote:
As a pet/learning project I made a data aquisition unit using an

8051
microprocessor and an EPIA M motherboard running a variant of Linux

to
process and display the information. It all works but the EMI from

the
EPIA M causes way too much noise to the aircraft radios. I have

tried
shielding the whole device in an aluminum case with very little
improvement.

Any ideas on how to smother the EMI or some other small motherboard
which may not have as much an issue (as a test I took my portable
aviation radio and within 6' of any my home computers the same

occurs
which gives me little hope)

Thanks


  #9  
Old January 27th 05, 02:06 PM
AINut
external usenet poster
 
Posts: n/a
Default

Look up info on "Tempest" PC's. Lots of good methods for RFI suppression.


jcpearce wrote:
Thanks for the suggestions, no I have not posted what I did anywhere
but I think I will as it took me a little while to learn rudimentary
assembly, come up with a variant of linux running off flash memory,
write the code to process the serial output and display etc..

I did not use a hobby aluminum case, I custom built one with no gaps
(motherboard has a temperature sensor so I could check this for
possible overheating) and this was grounded. Without hooking up the
data aquisition card and just powering up the EPIA M in the seperate
aluminum case with no connections of any kind to the airplane I get the
interference in the radio. There are no connections coming out of the
aluminum box except for power and this line has caps on it for
filtering.

So it is coming solely from the motherboard, some chip on the board is
oscillating in the 107~130 Mhz range, given this occurs against one
home computer running at 2Ghz, another at 2.4 Ghz and the EPIA and 500
Mhz I would guess it is some supporting chip, but even if I knew I am
not sure that would do me much good. Perhaps changing the aluminum case
to a different size/shape would catch the offending frequency but I am
in the dark here and would be shooting in the dark.

There only seems two generic routes,
A) find a small computer which does not emit these frequencies (but I
do not know what is emmiting them so I would not know which computer
choice would alleviate this)
B) Some vastly better shielding approach for the motherboard.

Ideas?

Thanks



Bob wrote:

The "noise" could be coming through the connector and could be


emitting

from the wires.

Try using a connector with a metal housing and backshell and wires


with

shields, terminate the shields to the connector backshell/housing


which

will ground to the chassis.

The other end of the wires, try to terminate their shields where they
connect to.

Aircraft environment is not the same as home environment. Different
applications different techniques.

jcpearce wrote:

As a pet/learning project I made a data aquisition unit using an


8051

microprocessor and an EPIA M motherboard running a variant of Linux


to

process and display the information. It all works but the EMI from


the

EPIA M causes way too much noise to the aircraft radios. I have


tried

shielding the whole device in an aluminum case with very little
improvement.

Any ideas on how to smother the EMI or some other small motherboard
which may not have as much an issue (as a test I took my portable
aviation radio and within 6' of any my home computers the same


occurs

which gives me little hope)

Thanks



  #10  
Old January 27th 05, 02:13 PM
Bob
external usenet poster
 
Posts: n/a
Default

Some IMPRESSIVE experience in this group.

I have not heard "tempest" in years.

But again, in my experience, if you've got a metal box already. It's
most likely the connector and harness.

Carry those grounds (on the harness shields) through!



AINut wrote:
Look up info on "Tempest" PC's. Lots of good methods for RFI

suppression.


jcpearce wrote:
Thanks for the suggestions, no I have not posted what I did

anywhere
but I think I will as it took me a little while to learn

rudimentary
assembly, come up with a variant of linux running off flash memory,
write the code to process the serial output and display etc..

I did not use a hobby aluminum case, I custom built one with no

gaps
(motherboard has a temperature sensor so I could check this for
possible overheating) and this was grounded. Without hooking up the
data aquisition card and just powering up the EPIA M in the

seperate
aluminum case with no connections of any kind to the airplane I get

the
interference in the radio. There are no connections coming out of

the
aluminum box except for power and this line has caps on it for
filtering.

So it is coming solely from the motherboard, some chip on the board

is
oscillating in the 107~130 Mhz range, given this occurs against one
home computer running at 2Ghz, another at 2.4 Ghz and the EPIA and

500
Mhz I would guess it is some supporting chip, but even if I knew I

am
not sure that would do me much good. Perhaps changing the aluminum

case
to a different size/shape would catch the offending frequency but I

am
in the dark here and would be shooting in the dark.

There only seems two generic routes,
A) find a small computer which does not emit these frequencies (but

I
do not know what is emmiting them so I would not know which

computer
choice would alleviate this)
B) Some vastly better shielding approach for the motherboard.

Ideas?

Thanks



Bob wrote:

The "noise" could be coming through the connector and could be


emitting

from the wires.

Try using a connector with a metal housing and backshell and wires


with

shields, terminate the shields to the connector backshell/housing


which

will ground to the chassis.

The other end of the wires, try to terminate their shields where

they
connect to.

Aircraft environment is not the same as home environment.

Different
applications different techniques.

jcpearce wrote:

As a pet/learning project I made a data aquisition unit using an


8051

microprocessor and an EPIA M motherboard running a variant of

Linux

to

process and display the information. It all works but the EMI from

the

EPIA M causes way too much noise to the aircraft radios. I have


tried

shielding the whole device in an aluminum case with very little
improvement.

Any ideas on how to smother the EMI or some other small

motherboard
which may not have as much an issue (as a test I took my portable
aviation radio and within 6' of any my home computers the same


occurs

which gives me little hope)

Thanks




 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 01:18 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AviationBanter.
The comments are property of their posters.