If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#81
|
|||
|
|||
SAFE Winch Launching
Don Johnstone wrote:
At 22:34 14 July 2009, Gary Emerson wrote: Just exacly where are you making these tensions measurements???? Are you making them at the weak link?? Are you making these measurements at the winch end of things? I'd really like to know... That is the question that is puzzling me too. The tension sensed by the winch will, and should be constantly changing during the launch, measuring that would be, how can I put it, useless. The tension at the glider release hook will be relatively constant but measuring that introduces the problem of the addional weight of the device that does it and a reliable transmission of data to the ground. Which is why I suggested we think about metrics. If there were not big changes in tension at the Winch end you would have a REAL problem. Go check it - on our 2km run the glider has not moved before the winch is 1-1.5s into power up - until then there is a lot of tension going into the cable at the winch and zero happening at the glider end. We have had a ham fisted learner winch driver snap the cable neatly (1880KN breaking strain cable) at the drum without even moving the chute at the launch point. So - The place it has to be reasonably gentle (smooth curve) is at the glider hook. Now we get into a whole new debate about the relative advantage of UHMDPE (Spectra / Dyneema etc.) and steel cable. Steel has much more elasticity and inertia to absorb those transient loads. The spring steel wire acts like a spring storing energy and smoothing loads. Inconveniently this means that when it breaks under tension you get a backlash that can result in big overwinds and injuries. The plastic rope is - counter-intutively given the name, far less elastic and very light. Result is that winches so equipped may need to have smoother delivery. And (I am not a good enough engineer here) it is possible that the tension at the winch on these is similar to that experienced by the aircraft hook. Would depend on hysteresis and all sorts of other things that are probably best measured rather than calculated / guessed. Any one with facts? |
#82
|
|||
|
|||
SAFE Winch Launching
"That pretty much means either finding a rebuildable Gehrlein,
importing an inexpensive used winch from Europe, or homebrewing a new winch (based on the UK spec). I prefer the latter, as I think there is still plenty of room for optimization, both in fabrication and operation. While I respect those who are trying to push the envelope with advance power systems and launch automation, a simple single drum winch based on automotive components will be good enough for our local group get started. " I agree, however, I suggest a retrieve winch set up if you guys are going for a single drum as otherwise, launch rate will be too slow. Last year I flew from a 6 drum winch and it was aircraft carrier style. From reading, I gather that with a single drum winch with a retrieve winch set up can achieve a rate of 20 launches an hour. How many tow planes would it take to achieve 20 launches/hour to 2,000 feet per launch? My guess is two tow plane. With only 1 tow plane that many launches would take 2 hours - much more if they stray far from the airport. The economics of winching are staggering compared to aerotows - and above all - much more fun. This includes hunting for that first lift at low altitude AGL. Even with multiple relights, it's still cheaper and more fun. Tom |
#83
|
|||
|
|||
SAFE Winch Launching
Generally speaking, the only way to break a weak link or a cable at the
start of a winch launch is to open the throttle wide before all of the slack has been taken out of the cable, so that you get a sudden snatch. I have launched on both stranded steel and UHMWPE cable on a conventional Tost winch with a changing automatic gearbox, and couldn't honestly feel any real difference, except that you don't get any jolts from cleated repairs going through the rollers with the synthetic cable. These generally occured near the top of the launch, where we were most likely to break cables with the Tosts, and are more down to the way we repair broken steel cables, rather than the cables themselves. I personally much prefer synthetic cables, because they give smoother and higher launches, but the club management said no, due to the much higher cost of the stuff! Dyneema is definitely safer in that it has less tendency to spring back after a break and no sharp ends to cut anybody who is unlucky or stupid enough to stand in the way. My club has had a couple of minor injuries that way. Derek Copeland At 06:55 15 July 2009, Bruce wrote: Which is why I suggested we think about metrics. If there were not big changes in tension at the Winch end you would have a REAL problem. Go check it - on our 2km run the glider has not moved before the winch is 1-1.5s into power up - until then there is a lot of tension going into the cable at the winch and zero happening at the glider end. We have had a ham fisted learner winch driver snap the cable neatly (1880KN breaking strain cable) at the drum without even moving the chute at the launch point. So - The place it has to be reasonably gentle (smooth curve) is at the glider hook. Now we get into a whole new debate about the relative advantage of UHMDPE (Spectra / Dyneema etc.) and steel cable. Steel has much more elasticity and inertia to absorb those transient loads. The spring steel wire acts like a spring storing energy and smoothing loads. Inconveniently this means that when it breaks under tension you get a backlash that can result in big overwinds and injuries. The plastic rope is - counter-intutively given the name, far less elastic and very light. Result is that winches so equipped may need to have smoother delivery. And (I am not a good enough engineer here) it is possible that the tension at the winch on these is similar to that experienced by the aircraft hook. Would depend on hysteresis and all sorts of other things that are probably best measured rather than calculated / guessed. Any one with facts? |
#84
|
|||
|
|||
SAFE Winch Launching
On Tue, 14 Jul 2009 21:19:50 -0700 (PDT), tommytoyz
wrote: The real cost of a winch launch is something like $3-5 per launch including maintenance, reserves and replacements. 30 launches a week x $10 profit = $1,200 extra a month. That's one very nice glider upgrade every 5 years. This is one of the main reasons why European clubs have such nice equipment. Unfortunately this is not the reason... There might be a few clubs in Europe that charge the prices you mentioned, but all the clubs I know charge between 2 and 5 Euro, sufficient only to cover the costs. Cheers Andreas |
#85
|
|||
|
|||
SAFE Winch Launching
I think all (certainly almost all) UK clubs charge the equivalent of
USD10 or more. Winch launching makes a surplus, aerotowing tends to run at a deficit, at the smaller clubs at least. Andreas Maurer wrote: On Tue, 14 Jul 2009 21:19:50 -0700 (PDT), tommytoyz wrote: The real cost of a winch launch is something like $3-5 per launch including maintenance, reserves and replacements. 30 launches a week x $10 profit = $1,200 extra a month. That's one very nice glider upgrade every 5 years. This is one of the main reasons why European clubs have such nice equipment. Unfortunately this is not the reason... There might be a few clubs in Europe that charge the prices you mentioned, but all the clubs I know charge between 2 and 5 Euro, sufficient only to cover the costs. Cheers Andreas |
#86
|
|||
|
|||
SAFE Winch Launching
Andreas,
At my old club in Germany there were several prices depending if you were a youth, club member in club aircraft, club member with your private aircraft or non club member with your private aircraft. The cheapest rates are as you mentioned. It also makes a big difference that the German clubs have way more launches than 30 a week. It's more like 150 a week or more. So the spread can be less. Of course there are other criteria that the government supports these clubs and some members to a small degree and they also charge by the hour for their aircraft - though a small fee - but a fee none the less. Their set up is just totally different, but my point is that you can make good money as a club here in the USA with a winch where you really can't with a tow plane. The tow plane is just very expensive if operated by the club and if using an FBO, no money comes back to the club. All this changes, with a club owned winch and even charging the astronomical fee (for a winch launch) of $15 per launch, it's a good money maker which can be put to good use in a non profit 501 (c)(3) club to buy aircraft, equipment, hangars, etc.....Even at $10 a launch it's a good money maker. Perhaps the launch fees can be charged as in the German clubs, depending on club status and aircraft. This would encourage club membership as well as it's cheaper to launch as a club member. |
#87
|
|||
|
|||
SAFE Winch Launching
At 08:05 15 July 2009, tommytoyz wrote:
Even with multiple relights, it's still cheaper and more fun. Tom Not if you finish up at the back of a queue of 20 gliders as the sea breeze blows through and the launch point has to be moved to the other end of the runway.... |
#88
|
|||
|
|||
SAFE Winch Launching
On Jul 15, 12:55*am, Bruce wrote:
Don Johnstone wrote: At 22:34 14 July 2009, Gary Emerson wrote: Just exacly where are you making these tensions measurements???? Are you making them at the weak link?? Are you making these measurements at the winch end of things? I'd really like to know... That is the question that is puzzling me too. The tension sensed by the winch will, and should be constantly changing during the launch, measuring that would be, how can I put it, useless. The tension at the glider release hook will be relatively constant but measuring that introduces the problem of the addional weight of the device that does it and a reliable transmission of data to the ground. Which is why I suggested we think about metrics. If there were not big changes in tension at the Winch end you would have a REAL problem. Go check it - on our 2km run the glider has not moved before the winch is 1-1.5s into power up - until then there is a lot of tension going into the cable at the winch and zero happening at the glider end. We have had a ham fisted learner winch driver snap the cable neatly (1880KN breaking strain cable) at the drum without even moving the chute at the launch point. So - The place it has to be reasonably gentle (smooth curve) is at the glider hook. Now we get into a whole new debate about the relative advantage of UHMDPE (Spectra / Dyneema etc.) and steel cable. Steel has much more elasticity and inertia to absorb those transient loads. The spring steel wire acts like a spring storing energy and smoothing loads. Inconveniently this means that when it breaks under tension you get a backlash that can result in big overwinds and injuries. The plastic rope is - counter-intutively given the name, far less elastic and very light. Result is that winches so equipped may need to have smoother delivery. And (I am not a good enough engineer here) it is possible that the tension at the winch on these is similar to that experienced by the aircraft hook. Would depend on hysteresis and all sorts of other things that are probably best measured rather than calculated / guessed. Any one with facts? As you point out, the mfg, spec's call for about 1.5% elongation at failure for UHMWPE (Spectra/Dyneema) That is much stiffer than steel. And yes, any roughness or variability in winch power output does get passed to the glider. That said, rope launches seem much smoother than with steel cable. A misconception seems to be that a tension controlled winch goes instantly from 0 to 100% tension at the beginning of the takeoff roll. In fact, tension ramps up smoothly and only becomes constant during the main climb. That's why it's called a "tension controlled winch" rather than a constant tension winch. The steady tension make it far easier for the pilot to maintain good airspeed control. There is much less effect from thermals and gusts. It's a quieter, smoother easier launch. Because the "area under the curve" is greater with constant tension in the main climb, more net energy gets transferred to the glider than in the case of varying tension so launches are higher with no increase in maximum climb angle. Tension through the ground roll and rotation phase follows essentially the same profile as with an excellent conventional winch launch. There are limits set to preclude too rapid acceleration and the tension cannot reach the weak link or rope breaking levels. The automation make one launch pretty much like the next with little variation due to the winch operator. By the way, tension control is nothing new. I recall an article in Sailplane and Gliding from the 1960's on the subject. Soaring Magazine had an article on an auto tow system using a tensiometer made from a hydraulic master cylinder and a pressure gauge from about the same time. Many of today's hang glider winches and auto tow systems use tension control. |
#89
|
|||
|
|||
SAFE Winch Launching
At 23:52 15 July 2009, bildan wrote:
A misconception seems to be that a tension controlled winch goes instantly from 0 to 100% tension at the beginning of the takeoff roll. In fact, tension ramps up smoothly and only becomes constant during the main climb. That's why it's called a "tension controlled winch" rather than a constant tension winch. The steady tension make it far easier for the pilot to maintain good airspeed control. There is much less effect from thermals and gusts. It's a quieter, smoother easier launch. Because the "area under the curve" is greater with constant tension in the main climb, more net energy gets transferred to the glider than in the case of varying tension so launches are higher with no increase in maximum climb angle. How can you possibly know that without measuring the "tension" at the release hook. You certainly cannot measure the increased tension caused by a thermal at the winch as the inertia of the steel cable is the main cause of the increase in tension experienced at the release hook. This "tension spike" cannot be measured at the winch. From a point at which the cable is at 45 degrees to the ground the "tension" imparted to the glider, through the cable release, is increasingly provided by the weight of the cable, and therefore measuring tension at the winch has no meaning whatsoever, in fact the tension there should be almost 0. Tension through the ground roll and rotation phase follows essentially the same profile as with an excellent conventional winch launch. There are limits set to preclude too rapid acceleration and the tension cannot reach the weak link or rope breaking levels. The automation make one launch pretty much like the next with little variation due to the winch operator. You may get good results by serendipidy but you certainly won't get them through control of tension. What you are measuring at the winch bears absolutely no direct relationship to what is experienced at the glider end, and that is what counts. With a good qualified winch driver you get consistent launches, sounds to me you are worrying far too much about not being able to train your winch drivers properly, and given some of the theories expounded that is perhaps understandable. What you are trying to achieve in a complicated way we solve by using robust equipment and trained winch drivers who do understand what they are doing. By the way, tension control is nothing new. I recall an article in Sailplane and Gliding from the 1960's on the subject. Soaring Magazine had an article on an auto tow system using a tensiometer made from a hydraulic master cylinder and a pressure gauge from about the same time. Many of today's hang glider winches and auto tow systems use tension control. |
#90
|
|||
|
|||
SAFE Winch Launching
On Jul 15, 7:00*pm, Don Johnstone wrote:
At 23:52 15 July 2009, bildan wrote: A misconception seems to be that a tension controlled winch goes instantly *from 0 to 100% tension at the beginning of the takeoff roll. *In fact, tension ramps up smoothly and only becomes constant during the main climb. *That's why it's called a "tension controlled winch" rather than a constant tension winch. The steady tension make it far easier for the pilot to maintain good airspeed control. *There is much less effect from thermals and gusts. It's a quieter, smoother easier launch. *Because the "area under the curve" is greater with constant tension in the main climb, more net energy gets transferred to the glider than in the case of varying tension so launches are higher with no increase in maximum climb angle. How can you possibly know that without measuring the "tension" at the release hook. You certainly cannot measure the increased tension caused by a thermal at the winch as the inertia of the steel cable is the main cause of the increase in tension experienced at the release hook. *This "tension spike" cannot be measured at the winch. From a point at which the cable is at 45 degrees to the ground the "tension" imparted to the glider, through the cable release, is increasingly provided by the weight of the cable, and therefore measuring tension at the winch has no meaning whatsoever, in fact the tension there should be almost 0. First, we're not using steel cable, we're using UHMWPE (Specra/ Dyneema). Lightweight "plastic" rope only weighs about 1 pound per hundred feet and has very little inertial at all. Tension measured at the winch is within a percent or so of that at the glider and has essentially no effect on tension measurement. Tension through the ground roll and rotation phase follows essentially the same profile as with an excellent conventional winch launch. There are limits set to preclude too rapid acceleration and the tension cannot reach the weak link or rope breaking levels. *The automation make one launch pretty much like the next with little variation due to the winch operator. You may get good results by serendipidy but you certainly won't get them through control of tension. Gee, I must be dreaming But we seem to be getting exactly what I'm telling you we're getting - with tension control. This isn't theory, we're actually doing it. There must be some sort of magic effect no one knows about. Or maybe the laws of physics are different over here. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Winch Launching in US | john hawkins | Soaring | 11 | June 10th 09 12:18 PM |
Winch Launching | Rolf | Soaring | 27 | January 7th 09 02:48 AM |
Ka8b winch launching | Jimmie L. Coulthard | Soaring | 11 | September 9th 08 08:38 AM |
Aerotow Fuel Costs & Winch Launching | Derek Copeland[_2_] | Soaring | 2 | May 26th 08 03:14 PM |
LIppmann reports a 950 meter winch launch with their Dynatec winch line - anything higher? | Bill Daniels | Soaring | 20 | December 27th 04 12:33 AM |