If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
PowerFLARM antenna mounts
Rex is looking into making glare-shield antenna mounts
for the PowerFLARM dipole antenna, especially for gliders with glare-shields that jettison with the canopy (Schleicher, LS). The mount will featu - mast sticks up above glare-shield - base mounts underneath glare-shield with velcro - anti-glare flat-black finish This arrangement permits safe canopy jettison and easy canopy removal. You'll cut a ~ 3-4" round hole in the glare-shield, afix the velcro, then stick on the antenna so it is vertical in flight attitude (with coax at about 45 degrees away from the antenna). Cost guestimated at $75 including shipping. Please send Rex an email if you're interested as he needs to gauge interest; contact info he http://www.williamssoaring.com Thanks, Best Regards, Dave "YO electric" PS: If you're interested in a mount for a flat-top glare-shield (SH, etc) - send Rex a note. |
#2
|
|||
|
|||
PowerFLARM antenna mounts
Having a glare-shield mounted antenna is like sitting behind a support column at a basketball game. No matter how hard you try, you are going to miss part of the game.
We seem content at compromising field-of-vision with cockpit reflections, compasses, PowerFlarm units and antennas, and multi-function displays. Yet, uncomprimised field-of-vision is our #1 accident preventer. PowerFlarmUSA...please find a better antenna solution. On Wednesday, July 4, 2012 11:50:53 AM UTC-4, Dave Nadler wrote: Rex is looking into making glare-shield antenna mounts for the PowerFLARM dipole antenna, especially for gliders with glare-shields that jettison with the canopy (Schleicher, LS). The mount will featu - mast sticks up above glare-shield - base mounts underneath glare-shield with velcro - anti-glare flat-black finish This arrangement permits safe canopy jettison and easy canopy removal. You'll cut a ~ 3-4" round hole in the glare-shield, afix the velcro, then stick on the antenna so it is vertical in flight attitude (with coax at about 45 degrees away from the antenna). Cost guestimated at $75 including shipping. Please send Rex an email if you're interested as he needs to gauge interest; contact info he http://www.williamssoaring.com Thanks, Best Regards, Dave "YO electric" PS: If you're interested in a mount for a flat-top glare-shield (SH, etc) - send Rex a note. |
#3
|
|||
|
|||
PowerFLARM antenna mounts
On Wednesday, July 4, 2012 12:16:38 PM UTC-7, (unknown) wrote:
Having a glare-shield mounted antenna is like sitting behind a support column at a basketball game. Complete Nonsense. The antenna and any decent mount are thin, and you won't notice them after 5 minutes. The angle blocked is only slightly more than your yaw string. Are you going to remove your yaw string too ? Really now. |
#4
|
|||
|
|||
PowerFLARM antenna mounts
On Wednesday, July 4, 2012 8:42:39 PM UTC-7, Dave Nadler wrote:
On Wednesday, July 4, 2012 12:16:38 PM UTC-7, (unknown) wrote: Having a glare-shield mounted antenna is like sitting behind a support column at a basketball game. Complete Nonsense. The antenna and any decent mount are thin, and you won't notice them after 5 minutes. The angle blocked is only slightly more than your yaw string. Are you going to remove your yaw string too ? Really now. No doubt PowerFlarm USA can come up with more aesthetic antenna and solutions. I will have to compromise meanwhile, but am expecting a better solution will followup shortly once they start shipping and have more time. The pictures I saw so far hurt my eyes... Ramy (who is eagerly waiting for his brick unit) |
#5
|
|||
|
|||
PowerFLARM antenna mounts
On Wednesday, July 4, 2012 11:50:53 AM UTC-4, Dave Nadler wrote:
Rex is looking into making glare-shield antenna mounts for the PowerFLARM dipole antenna, especially for gliders with glare-shields that jettison with the canopy (Schleicher, LS). The mount will featu - mast sticks up above glare-shield - base mounts underneath glare-shield with velcro - anti-glare flat-black finish This arrangement permits safe canopy jettison and easy canopy removal. You'll cut a ~ 3-4" round hole in the glare-shield, afix the velcro, then stick on the antenna so it is vertical in flight attitude (with coax at about 45 degrees away from the antenna). Cost guestimated at $75 including shipping. Please send Rex an email if you're interested as he needs to gauge interest; contact info he http://www.williamssoaring.com Thanks, Best Regards, Dave "YO electric" PS: If you're interested in a mount for a flat-top glare-shield (SH, etc) - send Rex a note. I'm not an antenna maven (certainly not at GHz frequencies, but we are talking about a device that operates at about the transponder frequencies. Transponder antennas are pieced of straight wire with a ground plane. Seems to me that it should be possible to craft a very good antenna from a piece of piano wire (read so thin it is virtually invisible) and a (sloped down a bit) ground plane. Any antenna geeks out there? QT Never confuse a graduate engineer with a competent technician... |
#6
|
|||
|
|||
PowerFLARM antenna mounts
On Thursday, July 5, 2012 7:48:21 AM UTC-4, John Godfrey (QT) wrote:
On Wednesday, July 4, 2012 11:50:53 AM UTC-4, Dave Nadler wrote: Rex is looking into making glare-shield antenna mounts for the PowerFLARM dipole antenna, especially for gliders with glare-shields that jettison with the canopy (Schleicher, LS). The mount will featu - mast sticks up above glare-shield - base mounts underneath glare-shield with velcro - anti-glare flat-black finish This arrangement permits safe canopy jettison and easy canopy removal. You'll cut a ~ 3-4" round hole in the glare-shield, afix the velcro, then stick on the antenna so it is vertical in flight attitude (with coax at about 45 degrees away from the antenna). Cost guestimated at $75 including shipping. Please send Rex an email if you're interested as he needs to gauge interest; contact info he http://www.williamssoaring.com Thanks, Best Regards, Dave "YO electric" PS: If you're interested in a mount for a flat-top glare-shield (SH, etc) - send Rex a note. I'm not an antenna maven (certainly not at GHz frequencies, but we are talking about a device that operates at about the transponder frequencies. Transponder antennas are pieced of straight wire with a ground plane. Seems to me that it should be possible to craft a very good antenna from a piece of piano wire (read so thin it is virtually invisible) and a (sloped down a bit) ground plane. Any antenna geeks out there? QT Never confuse a graduate engineer with a competent technician... Antenna QT describes will work for areas above the ground plane. I believe dipole is being used to provide a better transmission pattern both above and below the glider. Another voice. UH |
#7
|
|||
|
|||
PowerFLARM antenna mounts
On Wednesday, July 4, 2012 11:50:53 AM UTC-4, Dave Nadler wrote:
Rex is looking into making glare-shield antenna mounts for the PowerFLARM dipole antenna, especially for gliders with glare-shields that jettison with the canopy (Schleicher, LS). The mount will featu - mast sticks up above glare-shield - base mounts underneath glare-shield with velcro - anti-glare flat-black finish This arrangement permits safe canopy jettison and easy canopy removal. You'll cut a ~ 3-4" round hole in the glare-shield, afix the velcro, then stick on the antenna so it is vertical in flight attitude (with coax at about 45 degrees away from the antenna). Cost guestimated at $75 including shipping. Please send Rex an email if you're interested as he needs to gauge interest; contact info he http://www.williamssoaring.com Thanks, Best Regards, Dave "YO electric" PS: If you're interested in a mount for a flat-top glare-shield (SH, etc) - send Rex a note. Sloped groundplane (like base station antennas) should ensure propagation down to canopy rail angle. Need GHz antenna geek. |
#8
|
|||
|
|||
PowerFLARM antenna mounts
On Wednesday, July 4, 2012 11:50:53 AM UTC-4, Dave Nadler wrote:
Rex is looking into making glare-shield antenna mounts for the PowerFLARM dipole antenna, especially for gliders with glare-shields that jettison with the canopy (Schleicher, LS). The mount will featu - mast sticks up above glare-shield - base mounts underneath glare-shield with velcro - anti-glare flat-black finish This arrangement permits safe canopy jettison and easy canopy removal. You'll cut a ~ 3-4" round hole in the glare-shield, afix the velcro, then stick on the antenna so it is vertical in flight attitude (with coax at about 45 degrees away from the antenna). Cost guestimated at $75 including shipping. Please send Rex an email if you're interested as he needs to gauge interest; contact info he http://www.williamssoaring.com Thanks, Best Regards, Dave "YO electric" PS: If you're interested in a mount for a flat-top glare-shield (SH, etc) - send Rex a note. End fed dipole could also be very thin. |
#9
|
|||
|
|||
PowerFLARM antenna mounts
On Jul 4, 10:50*am, Dave Nadler wrote:
Rex is looking into making glare-shield antenna mounts for the PowerFLARM dipole antenna, especially for gliders with glare-shields that jettison with the canopy (Schleicher, LS). If the proposed alternative glare screen antenna mount comes to fruition, doesn't the coax between the unit and the antenna cause an impediment to the jettisoning of the canopy? Or is there a breakaway connection of some sort? You'll cut a ~ 3-4" round hole in the glare-shield, afix the velcro, then stick on the antenna so it is vertical in flight attitude (with coax at about 45 degrees away from the antenna). Out of curiosity, why such a large 3-4" hole? Is that so both antennas can stick through a single hole? Could you not drill two smaller holes at the correct spacing? Or do the pictures of the PowerFlarm I find at your site (which shows two small diameter antennas) differ from reality and we are now only have one antenna? Just don't want someone to needlessly emasculate their glare screen! Thanks, John |
#10
|
|||
|
|||
PowerFLARM antenna mounts
Googling "PowerFlarm antenna" I see both two antenna (thin or thick)
and single antenna installations. But I still don't get the 3-4" hole. Expiring minds want to know. And then this rather interesting picture of a PowerFlarm "Perfect" antenna location as mentioned by Craggy Aero. ;-) http://www.google.com/imgres?hl=en&b... r:0,s:0,i:73 Thanks, John |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
PowerFLARM Brick and PowerFLARM Remote Display Manuals Available | Paul Remde | Soaring | 30 | May 25th 12 11:58 PM |
PowerFlarm antenna install | Sam Zimmerman | Soaring | 10 | November 11th 10 09:54 PM |
Suction cup mounts | Ed Winchester[_2_] | Soaring | 2 | September 18th 09 03:58 AM |
PDA mounts | Mhudson126 | Soaring | 10 | May 19th 04 07:24 PM |
Commercial - New PDA mounts from RAM | Paul Remde | Soaring | 0 | September 11th 03 06:27 AM |