|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
|
|
#1
January 27th 12, 05:54 AM
posted to rec.aviation.soaring
|
|||
|
|||
Spar butt dimensions in 1-26E
All,
Does anyone happen to be near a 1-26E? I need to know the width and height of the spar butt. Thanks! Bart 
|
|
#2
January 27th 12, 01:25 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26E
Is it different from other models? I can be near an A/B in a couple of hours...
|
|
#3
January 27th 12, 03:19 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26
On Jan 27, 5:25*am, Papa3 wrote:
Is it different from other models? * I can be near an A/B in a couple of hours... I have no idea. If I had to I guess I would say that the dimensions will be either the same or very close. In any case, I am not risking much, so data for A/B will be welcome :-) Thanks, Bart
|
|
#4
January 27th 12, 05:03 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26E
On Jan 27, 12:54*am, Bart wrote:
All, Does anyone happen to be near a 1-26E? I need to know the width and height of the spar butt. Thanks! Bart Area going thru fuselage is about 7-1/2 high and 1 inch thick. UH
|
|
#5
January 28th 12, 03:25 AM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26E
On Jan 27, 9:03*am, wrote:
Area going thru fuselage is about 7-1/2 high and 1 inch thick. UH Just what I needed. Thank you! Bart
|
|
#6
January 30th 12, 06:06 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26E
On Jan 27, 7:25*pm, Bart wrote:
On Jan 27, 9:03*am, wrote: Area going thru fuselage is about 7-1/2 high and 1 inch thick. UH Just what I needed. Thank you! Bart It's a little bit thinner than one inch - maybe 0.9. A 0.75 thick plank fit just fine. Here is the result :https://picasaweb.google.com/ 106336048655464828909/126Restoration? authkey=Gv1sRgCI7IqLuM59WLRQ#5703476984381942690 Bart
|
|
#7
January 30th 12, 06:21 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26E
plank fit just fine. Here is the result :https://picasaweb.google.com/
106336048655464828909/126Restoration? authkey=Gv1sRgCI7IqLuM59WLRQ#5703476984381942690 Arrrgh. http://tinyurl.com/7w4yss8
|
|
#8
January 30th 12, 06:36 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26E
On Jan 30, 12:21*pm, Bart wrote:
plank fit just fine. Here is the result :https://picasaweb.google.com/ 106336048655464828909/126Restoration? authkey=Gv1sRgCI7IqLuM59WLRQ#5703476984381942690 Arrrgh.http://tinyurl.com/7w4yss8 looking nice! you going to paint it or polish?
|
|
#9
January 30th 12, 06:28 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26E
On Jan 30, 1:06*pm, Bart wrote:
On Jan 27, 7:25*pm, Bart wrote: On Jan 27, 9:03*am, wrote: Area going thru fuselage is about 7-1/2 high and 1 inch thick. UH Just what I needed. Thank you! Bart It's a little bit thinner than one inch - maybe 0.9. A 0.75 thick plank fit just fine. Here is the result :https://picasaweb.google.com/ 106336048655464828909/126Restoration? authkey=Gv1sRgCI7IqLuM59WLRQ#5703476984381942690 Bart I was doing it from memory- Geeeez! UH
|
|
#10
January 30th 12, 06:46 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Spar butt dimensions in 1-26E
On Jan 30, 10:28*am, wrote:
I was doing it from memory- Geeeez! UH Hey, I am not complaining! If I went by my memory, I would have assumed 1.5 inch :-) B.
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| The 747 butt wipe by A380!! | raamman | Simulators | 0 | May 3rd 10 06:36 PM |
| Storch (Butt ugly airplane!) | Glen in Orlando | Aviation Photos | 0 | October 26th 09 05:49 PM |
| Butt Ugly | Glen in Orlando[_3_] | Aviation Photos | 2 | December 19th 08 05:36 PM |
| A helicopter shaved my butt-hair !!!!!!!!!! | Bruno Beam | Rotorcraft | 1 | December 20th 04 08:24 PM |
| Spar Dimensions for J-3 and/or Aeronca Champ | Ron Wanttaja | Restoration | 2 | March 22nd 04 03:07 PM |
Hybrid Mode
