If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Air Compressor for RV Builder
What size air compressor do I need for building my RV-10? I don't know
about rivets and air tools. My experience is mostly carpentry. I may be interested in spraying some primer in interior areas but that's about as far as I'd go with painting. |
#2
|
|||
|
|||
John Bundy wrote:
What size air compressor do I need for building my RV-10? I don't know about rivets and air tools. My experience is mostly carpentry. I may be interested in spraying some primer in interior areas but that's about as far as I'd go with painting. Go to: http://www.matronics.com/search & get as many opinions as you can stand about air compressors directly from RV builders. If all you do is rivet & don't try to use spray guns or air powered die grinders (air drills are ok), a little 5 hp unit with 10-15 gal tank would be adequate. Type of compressor gets important if you don't care for noise (oilless is bad; old style piston type with oil in the crankcase is good). Charlie |
#3
|
|||
|
|||
"Charlie England" wrote in message ... John Bundy wrote: What size air compressor do I need for building my RV-10? I don't know about rivets and air tools. My experience is mostly carpentry. I may be interested in spraying some primer in interior areas but that's about as far as I'd go with painting. Go to: http://www.matronics.com/search & get as many opinions as you can stand about air compressors directly from RV builders. If all you do is rivet & don't try to use spray guns or air powered die grinders (air drills are ok), a little 5 hp unit with 10-15 gal tank would be adequate. Type of compressor gets important if you don't care for noise (oilless is bad; old style piston type with oil in the crankcase is good). .... forget about hp... it means NOTHING. That is why Campbell Hausfeld and other compressor companies have the lawyers swarming over them at the moment. I repeat: horsepower ratings for (most) compressors is bulls*hit and most people know that. Also, giving absolute numbers of XX gal size tank is also not useful information without knowing what tools you will be using. How to select a compressor: Find your most air hungry tool. Buy a compressor with more CFM than required at the PSI required for that tool. And then figure out how frequently that tool will run when selecting tank size. Continuous use tools like paint guns and die grinders would require a larger tank than 10-15 gal. HVLP guns typically require at least 13-15 CFM although there are a few low CFM HVLP guns available (Sharpe Platinum is one such gun). Or, just go with a conventional gun. I agree - get an oil lubed compressor simply due to the noise. And the oilless compressors do not last as long. Anyway: select the tools, then select the compressor. |
#4
|
|||
|
|||
In article ,
Charlie England wrote: John Bundy wrote: What size air compressor do I need for building my RV-10? I don't know about rivets and air tools. My experience is mostly carpentry. I may be interested in spraying some primer in interior areas but that's about as far as I'd go with painting. Go to: http://www.matronics.com/search & get as many opinions as you can stand about air compressors directly from RV builders. If all you do is rivet & don't try to use spray guns or air powered die grinders (air drills are ok), a little 5 hp unit with 10-15 gal tank would be adequate. Type of compressor gets important if you don't care for noise (oilless is bad; old style piston type with oil in the crankcase is good). Charlie One precaution id to drain the accumulated water out of the tank at least onece a week, as it can corrode the bottom and could result in a catastrophic tank rupture (about like a couple of sicks of dynamite). Always remember to turn it off when not in use! I was lucky with mine. I fired up the compressor and it seemed to take forever to reach shutoff pressure. As I approached it I heard a lot of hissing. I turned it off and let it depressurize. Later I found about a 1.5inch crack in the weld attaching the dome to the cylindrical part, in the bottom, of course! The funny thing, is that I had read an article in the Vintage about exploding air compressors (with pictures) and talked to the author at Oshkosh. This happened about 2 weeks after I returned from Oshkosh, so I figured out what was happening pretty fast. Fortunately, all I had to do was replace the tank, with a UL-approved type from Grainger's. |
#5
|
|||
|
|||
I did the sick puppy thing (refer recent posts!) and bought a second cheap
compressor from my local hardware warehouse outlet Bunnings (Australia). I already had the first one as a little unit I could take to work in the back of the wagon to us for blow dusting out the machines I repair. The second unit which cost all of $98.00 Australian (about US$2.73 going on the exchange rate that I seem to get at this end if I want to get anything in....) works just as well. They are made by GMC in China and have a simple 1500 watt motor and a 24 litre tank with two outlets, one direct from the tank and the other regulated. By connecting both together with a spare piece of hose between the two direct to tank outlets, I have both motors working together and both storage tanks. The regulating switches are quite close together and both cut in and out quite happily as I use the air in the combined tank. And the capacity of both motors running together is enough to keep up with my spray gun. Although this requires a second power point to plug it in, it is so cheap that it is a worthwhile cheats way of doing the job. The difference in noise is barely noticable as I set them up outside the shed. Hope this helps, Peter "John Bundy" wrote in message om... What size air compressor do I need for building my RV-10? I don't know about rivets and air tools. My experience is mostly carpentry. I may be interested in spraying some primer in interior areas but that's about as far as I'd go with painting. |
#6
|
|||
|
|||
Mike Fitzgerald wrote:
"Charlie England" wrote in message ... John Bundy wrote: What size air compressor do I need for building my RV-10? I don't know about rivets and air tools. My experience is mostly carpentry. I may be interested in spraying some primer in interior areas but that's about as far as I'd go with painting. Go to: http://www.matronics.com/search & get as many opinions as you can stand about air compressors directly from RV builders. If all you do is rivet & don't try to use spray guns or air powered die grinders (air drills are ok), a little 5 hp unit with 10-15 gal tank would be adequate. Type of compressor gets important if you don't care for noise (oilless is bad; old style piston type with oil in the crankcase is good). ... forget about hp... it means NOTHING. That is why Campbell Hausfeld and other compressor companies have the lawyers swarming over them at the moment. I repeat: horsepower ratings for (most) compressors is bulls*hit and most people know that. Also, giving absolute numbers of XX gal size tank is also not useful information without knowing what tools you will be using. How to select a compressor: Find your most air hungry tool. Buy a compressor with more CFM than required at the PSI required for that tool. And then figure out how frequently that tool will run when selecting tank size. Continuous use tools like paint guns and die grinders would require a larger tank than 10-15 gal. HVLP guns typically require at least 13-15 CFM although there are a few low CFM HVLP guns available (Sharpe Platinum is one such gun). Or, just go with a conventional gun. I agree - get an oil lubed compressor simply due to the noise. And the oilless compressors do not last as long. Anyway: select the tools, then select the compressor. You are absolutely correct about the way to select a compressor & about the HP myth. Everything you said (and a LOT more) is in the Matronics RV-list archives link I provided. For instance, what external accessories you will need if you paint using an oil-type compressor. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Homebuilt Aircraft Frequently Asked Questions (FAQ) | Ron Wanttaja | Home Built | 2 | February 2nd 04 11:41 PM |
Homebuilt Aircraft Frequently Asked Questions (FAQ) | Ron Wanttaja | Home Built | 1 | January 2nd 04 09:02 PM |
Homebuilt Aircraft Frequently Asked Questions (FAQ) | Ron Wanttaja | Home Built | 0 | October 2nd 03 03:07 AM |
Homebuilt Aircraft Frequently Asked Questions (FAQ) | Ron Wanttaja | Home Built | 4 | August 7th 03 05:12 AM |
Homebuilt Aircraft Frequently-Asked Questions (FAQ) | Ron Wanttaja | Home Built | 0 | July 4th 03 04:50 PM |