If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#81
|
|||
|
|||
Wind/Solar Electrics ???
On Wed, 21 Dec 2005 14:09:10 -0500, Steve Spence wrote:
wrote: George Ghio wrote: Tell us why anyone would modify a sine wave. It's called "engineering," George. Nick Really... Wouldn't they rather modify a square wave to approximate a sine wave? What would be the point of modifying a sine wave, when a sine wave (or close approximation) is the required result? I hope you're not serious here. They don't make a sine wave and modify it, they make a rectangular wave and call it a "modified sine wave" because it passes enough tests for harmonics and crap that it will run most stuff, and they can get away with it. ;-) Anybody wanna do an FFT of various duty-cycle waveforms, and give us real THD information, and how that relates to power factor, and etc, and etc, and etc? The one inverter I've ever had my hands on the guts of made a waveform like this: ---- ---- ---- | | | | | | - - - - - - | | | | | etc. - ---- ---- And the regulator was just based on an ordinary rectifier - they didn't care about RMS, or it was scaled to get "close enough". But I do wonder, what does the harmonic content really do when you vary the duty cycle? Some years ago, in the USAF, I saw some pulses on a spectrum analyzer, and they had some really pretty envelopes. :-) Thanks, Rich |
#82
|
|||
|
|||
Wind/Solar Electrics ???
Rich Grise wrote:
On Wed, 21 Dec 2005 14:06:05 -0500, Steve Spence wrote: philkryder wrote: "....We have a touch lamp that will not change state on MSW, but will on generator" Do you know if these new smaller Inverter style generators are a close enough approximation for things like the laser printer? Just how good are the "sine" like waves on them? I thought someone was going to put a 'scope on one... I don't have one (inverter/generator) to test. If it's a SW then yes, it will work. The HONDA EM50is claims to be a sine wave unit. It seems pretty obvious that a mechanical generator should put out a relatively pure sine wave - it's just this big rotating magnetic field and a couple of coils, after all. :-) As a matter of fact, it's a little hard for me to visualize how someone would make anything _other than_ a plain vanilla sine wave using just a rotating magnet and a coil. Thanks! Rich Inverter units do not provide mechanically driven electrical output to the load, they run it through an inverter for frequency and voltage control. -- Steve Spence Dir., Green Trust, http://www.green-trust.org Contributing Editor, http://www.off-grid.net http://www.rebelwolf.com/essn.html |
#83
|
|||
|
|||
Wind/Solar Electrics ???
Rich Grise wrote:
On Wed, 21 Dec 2005 14:09:10 -0500, Steve Spence wrote: wrote: George Ghio wrote: Tell us why anyone would modify a sine wave. It's called "engineering," George. Nick Really... Wouldn't they rather modify a square wave to approximate a sine wave? What would be the point of modifying a sine wave, when a sine wave (or close approximation) is the required result? I hope you're not serious here. They don't make a sine wave and modify it, they make a rectangular wave and call it a "modified sine wave" because it passes enough tests for harmonics and crap that it will run most stuff, and they can get away with it. ;-) Anybody wanna do an FFT of various duty-cycle waveforms, and give us real THD information, and how that relates to power factor, and etc, and etc, and etc? The one inverter I've ever had my hands on the guts of made a waveform like this: ---- ---- ---- | | | | | | - - - - - - | | | | | etc. - ---- ---- And the regulator was just based on an ordinary rectifier - they didn't care about RMS, or it was scaled to get "close enough". But I do wonder, what does the harmonic content really do when you vary the duty cycle? Some years ago, in the USAF, I saw some pulses on a spectrum analyzer, and they had some really pretty envelopes. :-) Thanks, Rich That's my point. There are modified square wave inverters (marketed as Modified Sine Wave), and there are "Sine Wave" inverters, which are really MSW's with such fine steps that finicky equipment can't tell the difference. There are a few folks on this group trying to justify the "Modified Sine Wave" sales moniker but there is no logic to it. Folks who should know better, but can't find it easy to "agree" with george even for a moment. It even kills me to do it, but hey, he has a point for once. -- Steve Spence Dir., Green Trust, http://www.green-trust.org Contributing Editor, http://www.off-grid.net http://www.rebelwolf.com/essn.html |
#84
|
|||
|
|||
Wind/Solar Electrics ???
On Wed, 21 Dec 2005 23:25:58 GMT, Rich Grise
wrote: On Wed, 21 Dec 2005 14:09:10 -0500, Steve Spence wrote: wrote: George Ghio wrote: Tell us why anyone would modify a sine wave. It's called "engineering," George. Nick Really... Wouldn't they rather modify a square wave to approximate a sine wave? What would be the point of modifying a sine wave, when a sine wave (or close approximation) is the required result? I only am posting this back to RAO as it's the only NG I receive out of the list. I hope you're not serious here. They don't make a sine wave and modify it, they make a rectangular wave and call it a "modified sine wave" because it passes enough tests for harmonics and crap that it will run most stuff, and they can get away with it. ;-) Switching supplies are very efficient. Unfortunately things making sin waves from DC are not. The faster you can turn the transistors on and off the less heat and more power you can get out of a still smaller, lighter, and *cheaper* power supply, or inverter. Without digging too deep, a square wave contains an almost infinite frequency range on the rise and fall times. Most likely many thousands of times higher in frequency than the fundamental square wave. If you poke said square wave with all it's noise into an L/C filter it'll round it off into more of an approximation of a sin wave. You only have to get rid of enough of the spikes/harmonics to keep from confusing what ever you plan on running off the thing. Anybody wanna do an FFT of various duty-cycle waveforms, and give us real THD information, and how that relates to power factor, and etc, and etc, and etc? You want power factor too? Lordy, when I think of the caps we used to switch in on the power mains at work depending on load. I doubt current and voltage were ever in phase. Well, maybe with the exception of the time we fired back up after doing PM on some switch gear and some one had forgotten to remove the jumpers. Boy, but that was noisy! It actually bent the cabinet doors into shallow U-shapes and those things were made of 1/8" thick steel and about 7 or 8 feet tall. The one inverter I've ever had my hands on the guts of made a waveform like this: ---- ---- ---- | | | | | | - - - - - - | | | | | etc. - ---- ---- And the regulator was just based on an ordinary rectifier - they didn't care about RMS, or it was scaled to get "close enough". They were just after "close enough". That's why the 400 watt PS in one computer here weighs about a pound. The 500 watt in two others are about 4# and the 630 is still heavier. BUT the 200 watt PS for my ham rig weighs over 30#. I have a 600 watt (12 VDC @ 50 A) PS under the desk that must weigh about 60 or 70#, None of the computer Power supplies cost much over $50. I think the 400 was about $35. The big one for the ham rig was several hundred dollars. I have seen inverters that did a pretty good job on the output wave form, but they were expensive and not nearly as efficient as the cheap ones as a good portion of their work went into heat. But I do wonder, what does the harmonic content really do when you vary the duty cycle? I would *guess* they would get pretty drastic at some portions depending on just how hard the thing is working. There's not much power in them so I'd expect to see them round off under load, but does the inverter use dynamic filtering or hard filtering? Which is a good way of saying I don't really know. :-)) Roger Halstead (K8RI & ARRL life member) (N833R, S# CD-2 Worlds oldest Debonair) www.rogerhalstead.com Some years ago, in the USAF, I saw some pulses on a spectrum analyzer, and they had some really pretty envelopes. :-) Thanks, Rich |
#85
|
|||
|
|||
Wind/Solar Electrics ???
On Wed, 21 Dec 2005 14:29:00 GMT, Matt Whiting
wrote: George Ghio wrote: Tell us why anyone would modify a sine wave. To vary the power delivered to a load. Chopping off part of a sine wave cycle is a standard means of power control. That makes three phase SCR (Silicon controlled rectifiers and not saturable core reactors) interesting as chopping off part of the wave form develops spikes and harmonics that tend to make the control of one phase interact with the others. I've built a lot of them for single phase control, but I never once was able to build one for three phase that didn't interact. Turn one up and maybe another would go up, Turn the second down and the other two might go up or down. Twas interesting:-)) which is probably why Saturable core reactors are so popular in industry. Now there is a controller that is a tad on the weighty side. Roger Halstead (K8RI & ARRL life member) (N833R, S# CD-2 Worlds oldest Debonair) www.rogerhalstead.com Matt |
#86
|
|||
|
|||
Wind/Solar Electrics ???
On 20 Dec 2005 22:50:51 -0800, "philkryder"
wrote: "....We have a touch lamp that will not change state on MSW, but will on generator" Do you know if these new smaller Inverter style generators are a close enough approximation for things like the laser printer? Just how good are the "sine" like waves on them? I thought someone was going to put a 'scope on one... The quality of the wave form is directly proportional to the money you put into it. I've used a small generator to power just about everything in here. I've since upped that to 9,500 watts continuous which seems to work well. It does tend to mess with the clocks if we're on generator power for more than a few hours. I've never had any problems with the computers of printers though. Roger Halstead (K8RI & ARRL life member) (N833R, S# CD-2 Worlds oldest Debonair) www.rogerhalstead.com |
#87
|
|||
|
|||
Wind/Solar Electrics ???
On Wed, 21 Dec 2005 23:16:55 GMT, Rich Grise
wrote: On Wed, 21 Dec 2005 14:06:05 -0500, Steve Spence wrote: philkryder wrote: "....We have a touch lamp that will not change state on MSW, but will on generator" Do you know if these new smaller Inverter style generators are a close enough approximation for things like the laser printer? Just how good are the "sine" like waves on them? I thought someone was going to put a 'scope on one... I don't have one (inverter/generator) to test. If it's a SW then yes, it will work. The HONDA EM50is claims to be a sine wave unit. It seems pretty obvious that a mechanical generator should put out a relatively pure sine wave - it's just this big rotating magnetic field and a couple of coils, after all. :-) As a matter of fact, it's a little hard for me to visualize how someone would make anything _other than_ a plain vanilla sine wave using just a rotating magnet and a coil. Purchase a cheap one. They must try. :-)) Roger Halstead (K8RI & ARRL life member) (N833R, S# CD-2 Worlds oldest Debonair) www.rogerhalstead.com Thanks! Rich |
#88
|
|||
|
|||
Wind/Solar Electrics ???
When a scope is put on the waveform the shape is a "modified sine wave" This is not a hard concept. "Steve Spence" wrote in message ... That's my point. There are modified square wave inverters (marketed as Modified Sine Wave), and there are "Sine Wave" inverters, which are really MSW's with such fine steps that finicky equipment can't tell the difference. There are a few folks on this group trying to justify the "Modified Sine Wave" sales moniker but there is no logic to it. Folks who should know better, but can't find it easy to "agree" with george even for a moment. It even kills me to do it, but hey, he has a point for once. -- Steve Spence Dir., Green Trust, http://www.green-trust.org Contributing Editor, http://www.off-grid.net http://www.rebelwolf.com/essn.html |
#89
|
|||
|
|||
Wind/Solar Electrics ???
I guess you have no experience with creating digital
waveforms with a D/A converter and computer algoryths then. "Keith Williams" wrote in message T... BS. Were it unfiltered aliasing would make the CD sound terrible. The filter has to be in there for any sampled system. They didn't "all of a sudden" figure out that they needed a filter. -- Keith |
#90
|
|||
|
|||
Wind/Solar Electrics ???
Roger wrote:
On Wed, 21 Dec 2005 14:29:00 GMT, Matt Whiting wrote: George Ghio wrote: Tell us why anyone would modify a sine wave. To vary the power delivered to a load. Chopping off part of a sine wave cycle is a standard means of power control. That makes three phase SCR (Silicon controlled rectifiers and not saturable core reactors) interesting as chopping off part of the wave form develops spikes and harmonics that tend to make the control of one phase interact with the others. I've built a lot of them for single phase control, but I never once was able to build one for three phase that didn't interact. Turn one up and maybe another would go up, Turn the second down and the other two might go up or down. Twas interesting:-)) which is probably why Saturable core reactors are so popular in industry. Now there is a controller that is a tad on the weighty side. The application I'm familiar with (well I was 10 years ago) was electrically fired glass melting units. The resistive load didn't much care about cross phase interference. :-) Matt |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Question on 172 M electrics... (1974 Skyhawk II) | [email protected] | Piloting | 8 | April 10th 04 04:52 AM |