If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#61
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
Mike,
Mark Hawkins has it working with iGlide via WiFi. Hmm. Are you sure? He wrote earlier that: 3. Have gotten it to connect via Bluetooth LE (BLE) to iSoar which seems to process the PF sentences just as it does from other devices As for iGlide, Air Avionics does not specify he https://www.air-avionics.com/?page_id=507 that it is able to do BLE, but they do AirConnect instead. T-Beam's are shipped with either RC4 or RC5 SoftRF firmware versions. NMEA TCP (AirConnect) option was not available at that time yet. So build of the firmware from current source code and re-flashing is necessary. I would also appreciate if someone will confirm that ForeFlight is dong fine with SoftRF over Garmin GDL90. I have not done it by myself yet, as well as never seen reports about that from builders worldwide. Linar. |
#62
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
On Tuesday, October 30, 2018 at 9:35:45 AM UTC-6, Linar Yusupov wrote:
Mike, Mark Hawkins has it working with iGlide via WiFi. Hmm. Are you sure? He wrote earlier that: 3. Have gotten it to connect via Bluetooth LE (BLE) to iSoar which seems to process the PF sentences just as it does from other devices As for iGlide, Air Avionics does not specify he https://www.air-avionics.com/?page_id=507 that it is able to do BLE, but they do AirConnect instead. T-Beam's are shipped with either RC4 or RC5 SoftRF firmware versions. NMEA TCP (AirConnect) option was not available at that time yet. So build of the firmware from current source code and re-flashing is necessary. I would also appreciate if someone will confirm that ForeFlight is dong fine with SoftRF over Garmin GDL90. I have not done it by myself yet, as well as never seen reports about that from builders worldwide. Linar. Linar, When I saw Ed A's post an hour or so ago, I asked Mark who uses the app and he replied exactly as I have indicated. Mike |
#63
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
When I saw Ed A's post an hour or so ago, I asked Mark who uses the app and he replied exactly as I have indicated. Ok. Good news! Thank you! |
#64
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
Can a softrf be integrated into an existing (FLARM) setup?
I'd like to keep the flarm for its proven anti-collision warnings, and add in the ability to see all the other stuff that the Softrf provides. However the two antennae will interfere with each other (?). |
#65
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
On Monday, November 5, 2018 at 9:04:22 AM UTC-8, John Wells wrote:
Can a softrf be integrated into an existing (FLARM) setup? I'd like to keep the flarm for its proven anti-collision warnings, and add in the ability to see all the other stuff that the Softrf provides. However the two antennae will interfere with each other (?). "interface" means so much asking that is pretty meaningless. What do you expect/want it to do? Work on separate displays? An integrated display? Provide what services? What FLARM do you have and what country are you in? In the USA do you have ADS-B Out? |
#66
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
I'd like to be able to take NMEA stream from the Softrf for NON-FLARM contacts. I'm happy to write software or whip up a little micro to merge this with the NMEA output from FLARM and present them on my xcsoar radar.
But I expect the Softrf antenna will negatively impact my flarm tx/rx and vice versa. I'm in the UK. CLASSIC Flarm. But at the high level I don't think this makes any difference. I'm happy to do a lot of the leg work myself but just wondered what was possible. |
#67
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
At 12:59 06 November 2018, John Wells wrote:
I'd like to be able to take NMEA stream from the Softrf for NON-FLARM contacts. I'm happy to write software or whip up a little micro to merge this with the NMEA output from FLARM and present them on my xcsoar radar. depending your skillset, it might be easier to review/adapt Xcsoar. I believe XCSoar uses the data from the first device with that kind of data. That is certainly the case for GPS. So you might have to modify the code so that "FLARM" data is accepted from several device. (flarm between quote because all traffic device are seen as flarm if using the flarm protocol) But I expect the Softrf antenna will negatively impact my flarm tx/rx and vice versa. If the SoftRF doesn't transmit and the antenna are not close there won't be interference. If the softRF transmit on the same or close by frequency as FLarm then we might have provlem if they both transmit exactly at the same time. -- Xtophe |
#68
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
Can a SoftRF be integrated into an existing (FLARM) setup?
If you are considering XCSoar as FMS software, you either: 1) wait until Max will release next 7.0 preview or 2) build your own XCSoar binary from current source code tree. ( make sure that this commit : https://github.com/XCSoar/XCSoar/com...5fd3abf08e09e3 is in there. ) However the two antennae will interfere with each other (?). 1) Two receivers typically do not affect each other when distance between them is more than 2X of max. antenna size. Otherwise even inactive 2nd receiver's antenna (as well almost any other metal object) will slightly alter characteristics of 1st receiver's antenna (such as RL, SWR, …) ; 2) SoftRF's transmitter is compliant with 1% duty cycle rule ; 3) in any doubts, SoftRF user can disable transmitter with "Tx Power" menu option: https://github.com/lyusupov/SoftRF/wiki/Settings After that, other traffic will not see you on this protocol, but you will still be able to see them all. |
#69
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
Neat... I'm already using v7 on a custom openvario.
Is it worth transmitting ogntp if I already have a flarm? |
#70
|
|||
|
|||
"Do It Yourself" airborne proximity warning device
On Tuesday, October 30, 2018 at 2:35:04 AM UTC-6, Linar Yusupov wrote:
Will this device work with iGlide on IOS? AirConnect compatible Wi-Fi connection service is active in the firmware's source code since October 9th. Known to work good with SkyDemon, Air Nav Pro. You could let us know if it works with iGlide too. Hello Linar, We experimented with our new Prime Mk II device last weekend. It was a non-flying day here in Colorado, so we ground tested it against a PowerFLARM in a parked Ventus. We successfully paired the device (using Wi-Fi) with XCSoar running on a Samsung Tab A tablet. Then, we tested it by walking up and down the taxiway and were pleased to see that our "glider" was clearly displayed on the Ventus FLARM display and the Ventus was displayed on our tablet. Mission accomplished, so far. Next step will be to set up an OGN receiver and do some flight testing. It's quite amazing that a DIY product that goes together in five minutes and costs about $50 can provide this kind of capability. (One of our members made the enclosure on his 3D printer.) Thank you Linar! Note: I was hoping to try it with iGlide on the iPhone X, but was not successful. I installed AirConnect on the iPhone but couldn't get them to link. I've never used AirConnect before and may not be configuring it correctly. Is there a secret to this? I would appreciate any helpful suggestions from anyone who has had success with iGlide. Mike, Mark ... any suggestions? Thanks, Ed A |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
"View Limiting Device" recommendations please | [email protected] | Instrument Flight Rules | 27 | February 4th 08 02:25 AM |
Monday 073007 in Oshkosh - Going Home [01/10] - "Departing Oshkosh - Airborne Inaging DC3C.jpg" yEnc (0/1) | Just Plane Noise[_2_] | Aviation Photos | 0 | August 2nd 07 04:39 AM |
Monday 073007 in Oshkosh - Going Home [01/10] - "Departing Oshkosh - Airborne Inaging DC3C.jpg" yEnc (1/1) | Just Plane Noise[_2_] | Aviation Photos | 0 | August 2nd 07 04:39 AM |
New traffic warning device | Loran | Products | 26 | February 18th 04 12:14 AM |
Plane with no stall warning device? | Roy Smith | General Aviation | 23 | February 17th 04 03:23 AM |