If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
engine trouble
I have about 1100 SMOH on my IO-360 (2000 TBO).
Compressions are all 70 or above. There was only a tiny bit of metal at the last oil change. That was shortyly after I bought it, at which time I also put a spin-on filter adapter on. The engine has been running great, especially lately. However, my mechanic was fighting a nagging problem. It seems the seal where the crank case halves come together leaks. Mine is/was leaking right on top of the engine. It was very disturbing for a while, but my mechanic managed to stop the leak with some silicone. I understand that taking it apart would be very expensive, so I've been pricing an overhaul. Looks like about $17K for an overhaul. I'd really like to milk it out closer to TBO. I'm wondering if I should continue to ignore the problem, as long as no oil is leaking, and the engine is running fine. It's been about three months since any problems, but I don't know how long it will hold. I've been flying a couple hours per week with not even a drip. Your suggestions would be appreciated. Adam N7966L Beech Super III |
#2
|
|||
|
|||
If it were me I would keep an eye on it and try to fly it
as long as possible until the leakage becomes worse. Bear in mind there is a big difference between a "small" leak and a "large" leak. |
#3
|
|||
|
|||
mindenpilot wrote: Your suggestions would be appreciated. You're considering doing an overhaul to fix an oil leak?!?!?!?!?! That's insane. George Patterson He who would distinguish what is true from what is false must have an adequate understanding of truth and falsehood. |
#4
|
|||
|
|||
"George Patterson" wrote in message ... mindenpilot wrote: Your suggestions would be appreciated. You're considering doing an overhaul to fix an oil leak?!?!?!?!?! That's insane. George Patterson He who would distinguish what is true from what is false must have an adequate understanding of truth and falsehood. When it *was* leaking, it was leaking pretty good. Now that it's stopped, I'm not as concerned. But, if the silicone doesn't hold, and the leak is really bad again, what options do I have? That's not a rhetorical question, I really would like to know... Thanks, Adam N7966L Beech Super III |
#5
|
|||
|
|||
"mindenpilot" wrote in message ... "George Patterson" wrote in message ... mindenpilot wrote: Your suggestions would be appreciated. You're considering doing an overhaul to fix an oil leak?!?!?!?!?! That's insane. George Patterson He who would distinguish what is true from what is false must have an adequate understanding of truth and falsehood. When it *was* leaking, it was leaking pretty good. Now that it's stopped, I'm not as concerned. But, if the silicone doesn't hold, and the leak is really bad again, what options do I have? That's not a rhetorical question, I really would like to know... Thanks, Adam N7966L Beech Super III R & R the silicone and buy a box of Scott disposable rags. |
#6
|
|||
|
|||
George Patterson wrote:
You're considering doing an overhaul to fix an oil leak?!?!?!?!?! That's insane. That's exactly what I had to do these past few months. Of course, the engine was well over TBO and the leak was coming from a cracked cylinder. -- Peter ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
#7
|
|||
|
|||
You might check into a "wicking sealant". I know permatex makes one, but I
don't know the part number. Do it at night since it is not aircraft stuff. It has worked for me on a variety of leaks on transmissions and transaxles. Of course you need to remove the RTV and clean the area with brake cleaner first. Mike MU-2 "mindenpilot" wrote in message ... I have about 1100 SMOH on my IO-360 (2000 TBO). Compressions are all 70 or above. There was only a tiny bit of metal at the last oil change. That was shortyly after I bought it, at which time I also put a spin-on filter adapter on. The engine has been running great, especially lately. However, my mechanic was fighting a nagging problem. It seems the seal where the crank case halves come together leaks. Mine is/was leaking right on top of the engine. It was very disturbing for a while, but my mechanic managed to stop the leak with some silicone. I understand that taking it apart would be very expensive, so I've been pricing an overhaul. Looks like about $17K for an overhaul. I'd really like to milk it out closer to TBO. I'm wondering if I should continue to ignore the problem, as long as no oil is leaking, and the engine is running fine. It's been about three months since any problems, but I don't know how long it will hold. I've been flying a couple hours per week with not even a drip. Your suggestions would be appreciated. Adam N7966L Beech Super III |
#8
|
|||
|
|||
"Mike Rapoport" wrote in message nk.net... You might check into a "wicking sealant". I know permatex makes one, but I don't know the part number. Do it at night since it is not aircraft stuff. It has worked for me on a variety of leaks on transmissions and transaxles. Of course you need to remove the RTV and clean the area with brake cleaner first. Mike MU-2 Good info. I'll keep this in mind if the leak comes back. Thanks Mike. Adam N7966L Beech Super III |
#9
|
|||
|
|||
On Sun, 06 Feb 2005 02:01:14 GMT, "Mike Rapoport"
wrote: You might check into a "wicking sealant". I know permatex makes one, but I don't know the part number. Do it at night since it is not aircraft stuff. It has worked for me on a variety of leaks on transmissions and transaxles. Of course you need to remove the RTV and clean the area with brake cleaner first. There is a letter circulating around from TCM concerning case seam leaks. The gist of the process is remove any leaking case bolts in the area, clean thoroughly with MEK (brake cleaner would work), and apply cyanoacrylate adhesive. That's right, super glue. You hook a shop vac up to the breather, turn it on, clean things up and let dry thoroughly. Turn the vac back on, apply the glue to the seam and on the inside of the bolt holes. Let it dry, put it all back together, torque the bolts and fly the crap out of it. Had really good luck using the extremely thin hobby stuff, then painting the thicker stuff down the seam (sparingly) after the thin stuff is dry. Is an "approved" repair for TCM products, and I have used it with good results. You hit the nail on the head, it is a "wicking" leak in most cases, and a wicking sealant will stop it... Regards; TC |
#10
|
|||
|
|||
Minor oil leakage seems to be a nagging problem with IO-360s. Our old
engine (in an Arrow IV) always leaked some oil for the last 1000 hours before we swapped it for a factory rebuilt. (At that point, the engine was actually beyond TBO, and leakage was not a major consideration in deciding to do the engine swap.) Every year during the annual our mechanic would chase down the leaks and do what he could to minimize them. One important step was retorqueing the case bolts. At worst, our oil consumption ran about 1 qt/6 hrs, including leakage. At that rate (which included "real" oil consumption as well as leakage), we were advised that our leakage was not serious -- really more of a nuisance, so we lived with it. One thing we learned with the old engine was that leakage was MUCH worse when the oil level was above about 6.5 qts. My recommendation: Sure, go ahead and have your A&P do use whatever simple means are available to minimize leakage, but unless it gets severe (1 qt per 4-5 hrs) I wouldn't go beyond that. -Elliott Drucker |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ROP masking of engine problems | Roger Long | Owning | 4 | September 27th 04 07:36 PM |
Proposals for air breathing hypersonic craft. I | Robert Clark | Military Aviation | 2 | May 26th 04 06:42 PM |
My Engine Fire!! | [email protected] | Owning | 1 | March 31st 04 01:41 PM |
Car engine FAA certified for airplane use | Cy Galley | Home Built | 10 | February 6th 04 03:03 PM |
Corky's engine choice | Corky Scott | Home Built | 39 | August 8th 03 04:29 AM |