If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Gear Warning Switches on a Mosquito
I'm going to install gear warning switches in my Mosquito. I'd
appreciate some advice on the location, type and mounting method of the microswitches. Thanks Scott |
#2
|
|||
|
|||
I've always preferred magnetic reed switches (~$2) since there is no contact
between the control system and the switch. The reed switch contacts are hermetically sealed in 2" long 3/16th dia glass tubes so dirt can't contaminate them. Additionally, they are unlikely to get out of adjustment. I install the reed switch on the fuselage wall with either epoxy or outdoor double sided foam tape. Then find the right place on a pushrod for the little magnet that activates the switch then epoxy it in place. Bill Daniels "scooter" wrote in message oups.com... I'm going to install gear warning switches in my Mosquito. I'd appreciate some advice on the location, type and mounting method of the microswitches. Thanks Scott |
#3
|
|||
|
|||
No matter how well you design, place and secure your switches, they may
(will, according to Murphy) fail someday. Flying for hours with the warning buzzer on is no fun! (been there, done that, got the t-shirt) I strongly recommend a switch or fuse/circuit breaker on the panel, so you can disengage the buzzer inflight. Happy Soaring, Lars Peder -- -- Lars P. Hansen "T o d d P a t t i s t" wrote in message ... "scooter" wrote: I'm going to install gear warning switches in my Mosquito. I'd appreciate some advice on the location, type and mounting method of the microswitches. A common generic glider installation uses two security alarm switches (the type used for doors and windows) that respond to a magnet. The two magnets are attached with tie wraps to control rods for the gear and airbrakes. The switches are mounted to the side of the fuselage. Alternatively, mechanically operated microswitches can be used. You can get them with levers or long wire whiskers that can be bent to a desired shape. I prefer the former, since there is no wear, less likelihood of interfering with the control system and they are easier to align or adjust (just move the magnet along the control rod). |
#4
|
|||
|
|||
I've landed gear up......once..(so far ).....with the gear warning blaring
in my ear....I was of course distracted at the time with other complications at the time.....landing at an airshow, on grooved pavement.in front of 1000's ) (do it with style)......with a Yellow PIK20.....left a nice bright 2" (graduating to about 10") mark on the runway.....I've also helped other troubleshoot problems with their gear warning systems that wouldn't always work...bad switches, bad switch locations, broken wires, dead batteries..... The problem though comes from having a system that you become accustomed to.and when it doesn't work, you more than likely land gear up.... Personally.I much prefer a good mental check-list......mine is still GUMP'S...worked in twins....works in gliders too... tim -- Wings & Wheels www.wingsandwheels.com "Lars P. Hansen" wrote in message . .. No matter how well you design, place and secure your switches, they may (will, according to Murphy) fail someday. Flying for hours with the warning buzzer on is no fun! (been there, done that, got the t-shirt) I strongly recommend a switch or fuse/circuit breaker on the panel, so you can disengage the buzzer inflight. Happy Soaring, Lars Peder -- -- Lars P. Hansen "T o d d P a t t i s t" wrote in message ... "scooter" wrote: I'm going to install gear warning switches in my Mosquito. I'd appreciate some advice on the location, type and mounting method of the microswitches. A common generic glider installation uses two security alarm switches (the type used for doors and windows) that respond to a magnet. The two magnets are attached with tie wraps to control rods for the gear and airbrakes. The switches are mounted to the side of the fuselage. Alternatively, mechanically operated microswitches can be used. You can get them with levers or long wire whiskers that can be bent to a desired shape. I prefer the former, since there is no wear, less likelihood of interfering with the control system and they are easier to align or adjust (just move the magnet along the control rod). |
#5
|
|||
|
|||
Lars P. Hansen wrote:
No matter how well you design, place and secure your switches, they may (will, according to Murphy) fail someday. Flying for hours with the warning buzzer on is no fun! (been there, done that, got the t-shirt) I strongly recommend a switch or fuse/circuit breaker on the panel, so you can disengage the buzzer inflight. Been there, done that! If your vario is a Cambridge 302, you can connect the switches to it for the warning alarm. It's alarm can be canceled by the pilot with the pushbutton on the unit. Other varios/flight computers may provide the same function. -- Change "netto" to "net" to email me directly Eric Greenwell Washington State USA |
#6
|
|||
|
|||
Tim Mara wrote:
I've landed gear up......once..(so far ).....with the gear warning blaring in my ear....I was of course distracted at the time with other complications at the time.....landing at an airshow, on grooved pavement.in front of 1000's ) (do it with style)......with a Yellow PIK20.....left a nice bright 2" (graduating to about 10") mark on the runway.....I've also helped other troubleshoot problems with their gear warning systems that wouldn't always work...bad switches, bad switch locations, broken wires, dead batteries..... The problem though comes from having a system that you become accustomed to.and when it doesn't work, you more than likely land gear up.... Personally.I much prefer a good mental check-list......mine is still GUMP'S...worked in twins....works in gliders too... tim I've been saved from a gear up landing at least 3 times by a warning system, including one at an airshow! I prefer both (checklist AND warning system), so there are two layers of protection. If the gear warning goes off, I know I've violated my checklist procedures, so I admonish myself severely and promise to do better next time. Yes, I was using a check list for the three times I almost landed gear up, but the procedure failed for the usual reasons: low, distracted, other traffic, request from the tower, etc. -- Change "netto" to "net" to email me directly Eric Greenwell Washington State USA |
#7
|
|||
|
|||
Eric Greenwell wrote: Lars P. Hansen wrote: No matter how well you design, place and secure your switches, they may (will, according to Murphy) fail someday. Flying for hours with the warning buzzer on is no fun! (been there, done that, got the t-shirt) I strongly recommend a switch or fuse/circuit breaker on the panel, so you can disengage the buzzer inflight. Been there, done that! If your vario is a Cambridge 302, you can connect the switches to it for the warning alarm. It's alarm can be canceled by the pilot with the pushbutton on the unit. Other varios/flight computers may provide the same function. -- Change "netto" to "net" to email me directly Eric Greenwell Washington State USA Thanks to all for the advice, pictures and concerns! I will still be a checklist user! Scott Elhardt Minnesota |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Aluminum vs Fiberglass landing gear - Pro's and cons. | Bart Hull | Home Built | 1 | November 24th 03 02:46 PM |
Aluminum vs Fiberglass landing gear - Pro's and cons. | Bart Hull | Home Built | 2 | November 24th 03 05:23 AM |
Aluminum vs Fiberglass landing gear - Pro's and cons. | Bart Hull | Home Built | 0 | November 24th 03 03:52 AM |
Aluminum vs Fiberglass landing gear - Pro's and cons. | Bart D. Hull | Home Built | 0 | November 22nd 03 06:24 AM |
gear warning plus | K.P. Termaat | Soaring | 0 | September 8th 03 08:33 AM |