A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Soaring
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

LX4000 and PDA



 
 
Thread Tools Display Modes
  #1  
Old September 20th 06, 01:30 PM posted to rec.aviation.soaring
Gabriel Duford
external usenet poster
 
Posts: 15
Default LX4000 and PDA

Hi!
Is there a way to connect an LX4000 into a PDA?
I am pretty sure there is an output on the LX4000, but there's no info
in my english version of the manual and the only manual available from
LX-Navigation is for v5.3 and is in German and doesn't have wiring
diagrams. I have an electronic German manual for v8.3 (which I have in
my LX4000) but there's no details about the output wiring.

My setup is: LX20 as logger and GPS source for the LX4000.
I'd like to: connect the PDA in the LX4000 to run something like XCSoar
or GPS_LOG.

Thanks,

gabriel

  #2  
Old September 20th 06, 03:18 PM posted to rec.aviation.soaring
Paul Remde
external usenet poster
 
Posts: 1,691
Default LX4000 and PDA

Hi Gabriel,

I suggest you send an e-mail to . I have received
many wiring diagrams from them upon asking in the past.

If you can't work it out yourself I can create a custom wiring harness for
you.

Good Soaring,

Paul Remde
Cumulus Soaring, Inc.
http://www.cumulus-soaring.com

"Gabriel Duford" wrote in message
ps.com...
Hi!
Is there a way to connect an LX4000 into a PDA?
I am pretty sure there is an output on the LX4000, but there's no info
in my english version of the manual and the only manual available from
LX-Navigation is for v5.3 and is in German and doesn't have wiring
diagrams. I have an electronic German manual for v8.3 (which I have in
my LX4000) but there's no details about the output wiring.

My setup is: LX20 as logger and GPS source for the LX4000.
I'd like to: connect the PDA in the LX4000 to run something like XCSoar
or GPS_LOG.

Thanks,

gabriel



  #3  
Old September 20th 06, 03:42 PM posted to rec.aviation.soaring
Gabriel Duford
external usenet poster
 
Posts: 15
Default LX4000 and PDA

Thank you Paul, I will email them.

Do you know if the LX4000 will send more than just a repeat of the NMEA
received from the GPS? Will it add some "compensated vario"
information that the software on the PDA can use (a little like the
LX1600 and many other varios do)?

Thanks again,

gabriel
p.s. Gilles-Andre, j'ai recu ton email, mais une erreur "unknown user"
me revient lorsque je reply. As-tu un autre email?

Paul Remde wrote:
Hi Gabriel,

I suggest you send an e-mail to . I have received
many wiring diagrams from them upon asking in the past.

If you can't work it out yourself I can create a custom wiring harness for
you.

Good Soaring,

Paul Remde
Cumulus Soaring, Inc.
http://www.cumulus-soaring.com

"Gabriel Duford" wrote in message
ps.com...
Hi!
Is there a way to connect an LX4000 into a PDA?
I am pretty sure there is an output on the LX4000, but there's no info
in my english version of the manual and the only manual available from
LX-Navigation is for v5.3 and is in German and doesn't have wiring
diagrams. I have an electronic German manual for v8.3 (which I have in
my LX4000) but there's no details about the output wiring.

My setup is: LX20 as logger and GPS source for the LX4000.
I'd like to: connect the PDA in the LX4000 to run something like XCSoar
or GPS_LOG.

Thanks,

gabriel


  #4  
Old September 20th 06, 04:16 PM posted to rec.aviation.soaring
Richard[_1_]
external usenet poster
 
Posts: 117
Default LX4000 and PDA

Gabriel,

I don't believe the LX4000 outputs vario data. But you can get Nav data
to your Pocket PC. Split the RX, TX, Ground from your LX20. Then to
a power converter Craggy Aero PWR-5B. This will pass the RX, TX data
to the Pocket PC and provide +5v to power the Pocket PC. A Y cable
could also be made to Supply RX, TX, GND to the LX4000 and RX, TX,
GND, 12v to the LX 20 from the PWR-5B.

Richard
www.craggyaero.com



Gabriel Duford wrote:
Hi!
Is there a way to connect an LX4000 into a PDA?
I am pretty sure there is an output on the LX4000, but there's no info
in my english version of the manual and the only manual available from
LX-Navigation is for v5.3 and is in German and doesn't have wiring
diagrams. I have an electronic German manual for v8.3 (which I have in
my LX4000) but there's no details about the output wiring.

My setup is: LX20 as logger and GPS source for the LX4000.
I'd like to: connect the PDA in the LX4000 to run something like XCSoar
or GPS_LOG.

Thanks,

gabriel


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 04:15 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AviationBanter.
The comments are property of their posters.