A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Home Built
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Looking for a reversible fuel transfer pump



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #11  
Old April 11th 05, 06:35 PM
external usenet poster
 
Posts: n/a
Default

X-No-Archive: yes

Jim Carriere wrote:
I've been toying with that idea for a while. You mean engine oil,
right?


Yes

Are such things at all common?


No, they are very uncommon.

I guess what I most wonder is
why, on GA aircraft with aircooled engines, are exhaust heat muffs
and/or fuel fired heaters commonplace.


Intentionally having a gasoline fire in the cabin was never my favorite

Which is worse, the
possibility of CO in the cabin or hot oil in the cabin (and possible
loss of powerplant lubrication)?


Velocity does it as a standard thing, they put their main oil cooler in
the nose an pipe hot oil to it from the engine. That always made me
nervous, though they haven't had a problem with it, and they put the
hose in conduit. I'm using an electric pump instead. I'm running much
lower pressure (just enough to overcome the friction of the oil moving
in the hose) and if it springs a leak, I can turn it off.

I'm also drawing oil from the side of the sump. There's space beneath
it for about 3 quarts, and another quart or so is in the upper part of
the case during flight. Lycoming says the engine can run without
damage on 2 quarts total.

In the worst case - a fitting fails just downstream from the pump, and
dumps oil in the back seat where I wont see it - the system will only
dump 2 quarts before the port is uncovered.


Seems to me that safety/reliability issues can be addressed by using
quality parts and design. The functionality issue is maintaining the


oil at operating temp, on a cold day or fast/high cruise, when cabin
heat is most needed and the engine does not want to run hot (cowl
flaps?).


When you're high cooling actually gets harder, because the air is thin.
The vernatherm will progressively cut off the main oil cooler as the
engine runs colder, but my cabin heat exchanger is only about 20% of
the size of the main. And my pump is putting out about 30-50% of the
volume of the engine oil pump. So I *think* that the total heat I'm
scavanging is not significant. If I find a part of the envelope where
it is (ultra-cold day, low power setting, low altitude) I can turn it
off, and I'm no worse off that I would be without it.


In other words, what am I missing? Thoughts anyone?


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Night flying in the mountians in a cessna 150, NW_PILOT Instrument Flight Rules 150 March 4th 05 06:13 PM
Night flying in the mountians in a cessna 150, NW_PILOT Owning 135 March 4th 05 06:13 PM
Replacing fuel cut-off valve with non-a/c part??? Michael Horowitz Owning 46 January 15th 05 10:20 PM
Anybody need a fuel transfer pump? Roy Smith Home Built 1 January 5th 04 05:53 PM
Pumping fuel backwards through an electric fuel pump Greg Reid Home Built 15 October 7th 03 07:09 PM


All times are GMT +1. The time now is 12:52 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AviationBanter.
The comments are property of their posters.