If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Older glass glider refinishing question
Group,
I am considering the purchase of an older glass bird in my local area. It has sat for quite a while and the finish is not the best. Specifically, someone shot Imron over the original gelcoat at some point in the past. (rather than take it down and refinish it correctly.) The Imron is now lifting/flaking in a few areas. (mostly the wing tips/upper surfaces) Obviously one option would be to completely refinish the glider in gelcoat. I doubt the glider is worth putting 15K worth of gelcoat on though. I figure the next option is to sand it down really well, do all the surface prep, filling and smoothing I could and then shoot more paint on the old gal. My concerns with this option is just how well I could expect the paint to hold up or look good over the gel coat. Third option....sand her down and fly her UGLY. I could put a bag over my head everytime I pulled her out and waited in the tow line. Of course this option costs nothing and I think it would be a perfectly flyable ship with a well sanded gelcoat and showing her age. Kinda like going to prom with your mother. Any thoughts, ideas or opinions? (About the glider not prom or mother.) Many thanks, GR |
#2
|
|||
|
|||
You don't say what the glider is, Slingsby Vegas are painted with acrylic as
standard. Peter S "Gus Rasch" wrote in message om... Group, I am considering the purchase of an older glass bird in my local area. It has sat for quite a while and the finish is not the best. Specifically, someone shot Imron over the original gelcoat at some point in the past. (rather than take it down and refinish it correctly.) The Imron is now lifting/flaking in a few areas. (mostly the wing tips/upper surfaces) Obviously one option would be to completely refinish the glider in gelcoat. I doubt the glider is worth putting 15K worth of gelcoat on though. I figure the next option is to sand it down really well, do all the surface prep, filling and smoothing I could and then shoot more paint on the old gal. My concerns with this option is just how well I could expect the paint to hold up or look good over the gel coat. Third option....sand her down and fly her UGLY. I could put a bag over my head everytime I pulled her out and waited in the tow line. Of course this option costs nothing and I think it would be a perfectly flyable ship with a well sanded gelcoat and showing her age. Kinda like going to prom with your mother. Any thoughts, ideas or opinions? (About the glider not prom or mother.) Many thanks, GR |
#3
|
|||
|
|||
Hi GR,
It's winter, what else you got to do. Start refinishing the sucker. All the urethane must be removed and any lose, cracked or pealing gel-coat, also. Get an air supply and an air-board (2.5 X 18) Jump on her with 40 grit, when your new air-board is completely worn out, you should be about ready to prime and then contour, by hand with 60 grit on a 2.5 X 18 board. Tidy up the 60 grit scratches with some 120 free hand work (those scratches give the paint *tooth*) Now your ready to shoot acrylic urathane. Give her 3 medium to wet coats and then contour with 600 wet followad by 800 wet. Now jump on her with your wool buffer and liquid buffing compound. Buff out at least twice. Put your numbers back on, stick-on are easiest, then wax, after the paint is at least a month old. By now it should be spring. Take your nice little cutie out and let all the other guys drool. JJ Sinclair |
#4
|
|||
|
|||
"Gus Rasch" wrote in message
om... Group, I am considering the purchase of an older glass bird in my local area. It has sat for quite a while and the finish is not the best. Specifically, someone shot Imron over the original gelcoat at some point in the past. (rather than take it down and refinish it correctly.) The Imron is now lifting/flaking in a few areas. (mostly the wing tips/upper surfaces) Obviously one option would be to completely refinish the glider in gelcoat. I doubt the glider is worth putting 15K worth of gelcoat on though. I figure the next option is to sand it down really well, do all the surface prep, filling and smoothing I could and then shoot more paint on the old gal. My concerns with this option is just how well I could expect the paint to hold up or look good over the gel coat. Third option....sand her down and fly her UGLY. I could put a bag over my head everytime I pulled her out and waited in the tow line. Of course this option costs nothing and I think it would be a perfectly flyable ship with a well sanded gelcoat and showing her age. Kinda like going to prom with your mother. Any thoughts, ideas or opinions? (About the glider not prom or mother.) Many thanks, GR I don't know how bad the finish is on your prospective purchase but the best advice may be, "ignore the finish and fly it the way it is." The advice I'm getting is that it won't hurt anything if you keep it dry and protected from UV. Others may giggle at your ugly glider but you will be enjoying the performance for a LOT less money. The gel-coat on my Nimbus 2C is probably worse the glider that you are looking at but it flies fine. I had the chance to fly in close with another beautifully finished Nimbus 2 for a couple of hours and any difference was undetectable. I may still want to re-finish it but improving the performance alone doesn't seem a good enough reason to do so. Following up on the re-finish ideas, I'm thinking of stripping the old gel-coat myself as JJ suggests but let an expert do the rest of the job. Anyone have thoughts on that? How much money can you save? Bill Daniels |
#5
|
|||
|
|||
|
#6
|
|||
|
|||
"Bill Daniels" wrote in message k.net...
I don't know how bad the finish is on your prospective purchase but the best advice may be, "ignore the finish and fly it the way it is." The advice I'm getting is that it won't hurt anything if you keep it dry and protected from UV. Others may giggle at your ugly glider but you will be enjoying the performance for a LOT less money. The gel-coat on my Nimbus 2C is probably worse the glider that you are looking at but it flies fine. I had the chance to fly in close with another beautifully finished Nimbus 2 for a couple of hours and any difference was undetectable. I may still want to re-finish it but improving the performance alone doesn't seem a good enough reason to do so. Following up on the re-finish ideas, I'm thinking of stripping the old gel-coat myself as JJ suggests but let an expert do the rest of the job. Anyone have thoughts on that? How much money can you save? Bill Daniels Bill, I am leaning towards sanding off the old paint to get it reasonably smooth and flying it UGLY. I can always paint or refinish it next winter after getting a season under my belt. GR |
#7
|
|||
|
|||
By now it should be spring. Take your nice little cutie out and let all the
other guys drool. JJ Sinclair I am leaning towards just sanding and flying it UGLY for the first season. I can always paint or redo the finish properly NEXT winter. Or maybe do it progressivley: One wing this year, do the other one next year. It will look a bit odd with one beautiful wing and one ... not so good. Or do just the elevator and see how it goes, so you can judge the amount of time better! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
molding plexiglas websites? | [email protected] | Owning | 44 | February 17th 05 09:33 PM |
Glass Cockpit in Older Planes | Charles Talleyrand | Owning | 2 | May 20th 04 01:20 AM |
C182 Glass Panel | Scott Schluer | Piloting | 15 | February 27th 04 03:52 PM |
2 glass HUD question | Jim Yanik | Military Aviation | 0 | January 30th 04 02:22 AM |
Discus Wing question | John Galloway | Soaring | 6 | August 23rd 03 07:52 AM |