Removing decals

[[email protected]]

Our club just received our newest 172. The previous owner put a decal
on the door advertising his company and we would like to remove it
without harming the paint. Any suggestions?

[Newps]

WD40

wrote:
> Our club just received our newest 172. The previous owner put a decal
> on the door advertising his company and we would like to remove it
> without harming the paint. Any suggestions?
>

[Paul kgyy]

Depending on the type of decal, a hair dryer might work.

[George Patterson]

wrote:
> Our club just received our newest 172. The previous owner put a decal
> on the door advertising his company and we would like to remove it
> without harming the paint. Any suggestions?

Here are three.....
http://sportbikeguy.com/garage/floor/decalrm.html
http://www.f500.org/pipermail/f500/2001q4/005348.html
http://www.finescale.com/fsm/community/forum/topic.asp?TOPIC_ID=9854

George Patterson
Give a person a fish and you feed him for a day; teach a person to
use the Internet and he won't bother you for weeks.

[Scott Migaldi]

wrote:
> Our club just received our newest 172. The previous owner put a decal
> on the door advertising his company and we would like to remove it
> without harming the paint. Any suggestions?
>
Hair dryer, plastic spoon, and patience

--
--------------------
Scott F. Migaldi
CP-ASEL-IA
N8116B

PADI MI-150972
Join the PADI Instructor Yahoo Group
http://groups.yahoo.com/group/PADI-Instructors/

--------------------

[Jim Burns]

3M Adhesive Remover
http://www.3m.com/product/a_index/Adhesive_Remover,_3M(TM)_General_Purpose_(BK)_00.j html

Jim

> wrote in message
oups.com...
> Our club just received our newest 172. The previous owner put a decal
> on the door advertising his company and we would like to remove it
> without harming the paint. Any suggestions?
>

[Bob Noel]

In article . com>,
wrote:

> Our club just received our newest 172. The previous owner put a decal
> on the door advertising his company and we would like to remove it
> without harming the paint. Any suggestions?

I used an old credit card and lots of patience to remove a decal from
the tank of my motorcycle. This was one of those decals designed to
breakup if removed. The use of a hair dryer seemed to be ineffective
(and I didn't push it because it was, after all, a gas tank).

A little polishing compound and you can't tell there was ever a decal.

--
Bob Noel
no one likes an educated mule

[Mike Spera]

wrote:

> Our club just received our newest 172. The previous owner put a decal
> on the door advertising his company and we would like to remove it
> without harming the paint. Any suggestions?
>
I have extensive experience removing decals. I used to remove the "wood
grain" decals from station wagons many years ago. Also, I worked in a
computer leasing company that shipped machines out with several stickers
all over them that had to eventually be removed and replaced when they
got too deteriorated.

For 3M vinyl like wood grain and modern graphics, use a heat gun and
work slowly. Another poster listed 3 sites that have very good info. If
the decal is aged and has been exposed to sunlight, it may be too
brittle and snap apart when you try to remove it. A plastic Bondo
squeegee may help, but it is a real pain in the ass when they do this.
If they are cracked, you can try 3M decal or adhesive remover.

It is a delicate balancing act to get the right "peel speed" on these
buggers when using heat. Also, heat guns can burn you, the decal, and
the underlying paint in an instant. So, you have to be VERY careful and
move the gun around CONSTANTLY. I had a guy who was pretty good at using
an acetylene torch as the heat source. I preferred the heat gun.

3M also makes an "eraser" for decal glue that often works on the decal
itself. The unit chucks into a drill and has some sort of rubber wheel.
It was made to remove the glue holding side moldings to cars but we
found it useful for other cleanups like this. Not sure if it is still made.

When you remove the decal, you may be in for a surprise. Some paint
finishes fade within 3 weeks of application. Decals applied at the wrong
time may leave an off colored spot that may or may not eventually fade
to match the surrounding area. Usually, the discolored spot is as
objectionable as the decal that caused it.

Good Luck,
Mike

[George Patterson]

Mike Spera wrote:
>
> 3M also makes an "eraser" for decal glue that often works on the decal
> itself. The unit chucks into a drill and has some sort of rubber wheel.
> It was made to remove the glue holding side moldings to cars but we
> found it useful for other cleanups like this. Not sure if it is still made.

It and others like it are still made. I didn't post links to the two I found
because they're pretty expensive.

George Patterson
Give a person a fish and you feed him for a day; teach a person to
use the Internet and he won't bother you for weeks.