We are looking for 2-3 UPCO S-III-S ejection seats in flightworthy condition or (at the most) in need of refurbishment Thanks, Rafi Yoeli www.urbanaero.com

"Well done, good and faithful servant" Mike, you handled this newsgroup "situation" admirablely in my opinion (no doubt not worth much here). This web board is in desperate need of a modicum of civility (a large dose is probably to much to ask). It goes way beyond normal or reasonable bantering...

Wooduuuward wrote in message I read that the R44 sales have 'taken off'. From frequently browsing the FAA crash reports, the R22 is listed almost every other week there. The R44 is larger, faster and flys higher. Is it safer? i.e.: in the last month: there are four incidents listed for...

Hello All, I've heard a rumor that Airmaster, the NZ maker of electric variable pitch propellers, is no longer around or on its last legs. Can anyone verify this please? Calvin

In article , writes: I was just wondering, are the uber hackers still on RAH? I have a problem with windows XP that nobody's been able to fix. I have a good suggestion but I doubt that you would take it.

At Arlington today, the following rah ilk were spotted, foraging amongst the dry grass and halter tops: Ron "the Red" Waantaja was seated in a custom 3" high lawn chair emblazoned with a Flybaby logo - under Moonraker's wing. He seemed kind of low. John Ousterhout, having spent the night with...

Anyone have phone number or contact info - thanks

I am wondering... My Sonerai has 4 stub exhausts cut to a 45 degree angle facing forward for some back presssure. I want to add some silencers to my setup. (Maybe one on each side...) Is it important that the distance from each cilinder exhaust port to the silencer is exactly equal or can I have...

Ken Evoy must be bonkers - or the smartest marketer around. He's just spent three months writing a 224-page manual for affiliates, telling you, step-by-step, how to succeed with revenue sharing programs . . . And now he's giving it away. All you have to do to get the complimentary manual...

Has anyone had any experience with the "gasflow" of VW engine to improve horsepower at lower RPM? ------------------------------------------------- If by 'gasflow' you mean volumetric efficiency, I've some experience in that area. I'll also assume your question hinges on the fact that maximum...

Folks - I know that if I get someone to sit inside and hold the flat Tinnerman fastener, I can screw in a machine screw from beneath the a/c. This is not the type of fasterner that clips on to the edge of the metal. For one person trying to either install or remove a screw from the afore mentioned...

I found out yesterday that Port Orchard airport (4WA9) will temporarily close tomorrow, July 14, for two weeks or so. The owners are ripping out the existing blacktop and going to repave. The taxiway was taken out Friday. It's the "or so" that bothers me. I can only hope the project is...

Folks - The oil pressure sensor/tube is secured to the engine block of my A-65 by a brass connector which is getting pretty chewed up; Over the years previous owners apparently using something other than the correct tool to tighten it down. I'm told (please correct me if my understanding is...

So can one use T88 to glue bell cranks to spars on flaps?

"pac plyer" wrote The same could be done for part 91 flight. We could all write Phil Boyer at AOPA and Paul Jr. at EAA and suggest arming ourselves at little airports across America. This would keep non-flying TSA drones out of our hair while at the same time...

Three of my students and I took the 206 to Arlington yesterday. We had to go IFR since the ceiling at Tacoma Narrows was only 400 feet. However, we broke out on top at 1400 and sailed under clear blue skies to Arlington, which was clear below 11,000. I was concerned about getting in there IFR and...

Chris At you talking about throtttle setting?. To hold the same % POWER as you climb, you have to advance the throttle until you get WOT from which point the % power decreases as you continue the climb. Big John Point of the sword On Thu, 10 Jul 2003 23:10:39 GMT, Chris W wrote:

There is a computer design program on my web-page www.jcpropellerdesign.com The program also content a help page. Also, Eric Clutton's booklet have some good praktical tips. best Jan Carlsson "AWV" skrev i meddelandet ... I would like to...

Ernest Christley misfired the following: I'm about halfway through this book. It is quite an eye opener. The author's explanations seem so insightful, cogent and complete. However, there's this one blemish. Printed in 1944, the author makes the claim that the rudder will disappear in just a...

Last year, after Oshkosh, someone posted a web site that had a very nice collection of photos in a slide show sort of format. They showed, in part, the planes around his in the show plane parking area. One of the photos was a DC 3 I believe firing up its' engines with a great cloud of smoke. I...