I've recently bought a glider that has an older Becker transponder(mode c), and every time I turn it on it invariably displays the E10 error code. In reading past reports of this issue(2006/2008) on the net this seemed to be a fairly common occurence, with no real solution. Becker says its a...

I am finding the summer heat to be quite difficult to manage in the southwestern USA. At the moment I have just been shoving a water bottle in my pocket but this proves to be somewhat uncomfortable and more of a pain in the rear to remove and use which makes me not drink as much as I maybe should....

I used to buy 1� tape to seal my wing/fuselage and the rest from Uline. Inside of the roll the only thing it says is 3M Scotch. Does anyone know the exact type? Thanks.

Has anyone received this? The digital version still shows latest edition as March. My email to glidinginternational last week asking for an update has been unanswered. On Friday, April 20, 2018 at 6:15:17 AM UTC+1, wrote: Hi Enthusiasts Our May issue will...

So I'm headed to Moariarty from TN with my 20 in tow in June. I have an older komet trailer, for which I had just gotten new tires, which I have yet to put on. I took the trailer to a shop locally to have the surge breaks adjusted, tires put on, and bearings repacked. After about an hour they...

I'm sure someone has come up with a much more user friendly system for self rigging vs. what I'm currently doing. My new to me DG400 is in an older Minden trailer, which is tucked inside a T-hangar behind a Cessna 182(high wing). To get the DG out I first have to pull the 182 out, than roll the...

I've seen them mounted in various places, under the seat pan would be ideal but I'm a bit painted into a corner at this point and it would need to be mounted in the panel, fairly near the radio and the ISU for the Air Vario. They claim these are well shielded, but I've been misled before by...

https://www.reuters.com/article/us-arevo-3dbike/silicon-valley-startup-peddles-3d-printed-bike-idUSKCN1II1LO "... the world’s first carbon fiber bicycle with 3D-printed frame. .... to demonstrate its design software and printing technology, which it hopes to use to produce parts for bicycles,...

Op woensdag 10 februari 1999 09:00:00 UTC+1 schreef Jon Vedum: Does anyone have practical experience with this plane? We are discussing buying one, so thanks for any comments. -- Jon Hi All, Are still parts for this plane for sale? I searched on line but not much luck. It might be my...

I have a 1979 Brazov IS29-D2 Lark. The rubber donuts are starting to wear out and get brittle on the main gear shock absorber. Does anyone know where I could get replacements? Either used from another glider, or manufactured new by someone who can match the donuts to the original spec?

I bought a single seat Lark and am beginning to build some time in it. Just wondering if there are any other Lark guys out there. I made a page on facebook as well if anyone of you wants to connect there. I had some time in the 2 place years ago, seemed to be a good flyer for what it was. I...

Would anyone have a single line diagram for a Dittel Speaker Box for two microphones? Mine is acting up and I found one additional cable soldered in - can't figure out what it is for and would like to find out what it connects to. Thanks, Uli 'AS'

I can't seem to send a usable link of one of my flight logs to a friend. The friend is not logged into Glideport. The link I copied from when I was looking at the track (and logged in) shows no tracks when the friend uses the link. A link to a search by pilot name, with my name, works when I log...

I finally got my new radio wired, the audio seems a little quiet compared to the old Dittel 71. Same speaker, 4 ohm as spec'd. I remember the Dittel being pretty loud, kept the volume knob set to the lower half of rotation. The Becker even at 100% is far from earsplitting, and maybe not loud...

Does anyone know how I could get a set of templates for my Standard Austria S? The airfoil is NACA 65(2)-415. Thanks, Jeff

This 2-33 is up for a salvage bid. If you look at the photos, there is no vario in the glider! Boggs

Just purchased the Wifi option for the LXNAV 9070. Currently I have a USB extension plugged into the only USB port on LX, then mounted on the panel fairing by my legs. This way I have access to the USB and all the data transfer without removing canopy to access port. My question is, can anyone...

Looking locally for one but so far the local electronic parts stores are baffled. If anyone here familiar with it, is there a source outside of Cambridge? Thanks Mike

Here's a conceptually simple idea for contest pilots to rattle around... I believe it would be highly effective at reducing dangerous big gaggles that happen during contests. The desirables are that it doesn't damage the sport, it's effective at improving safety, it's easy to understand and it's...

RAS, I'm pleased to announce that the Kansas Soaring Association is hosting Region 10 North at the Sunflower Aerodrome near Yoder, KS this year. Practice June 9-10 and Contest June 11-16. We hope you can join us! Kansas is conveniently located approximately half way between the East Coast and the...