A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Owning
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

sticky valve or



 
 
Thread Tools Display Modes
  #1  
Old May 22nd 05, 02:10 PM
external usenet poster
 
Posts: n/a
Default


Scott wrote:
Try the MARVEL!! We've been using it (dad & I) for 30 some years

mixed
in with the gas but I now think I will also use some in the oil).

The
first time I didn't use it (along with 100LL on a cross country trip)

I
stuck a valve with my A-65. Ran Marvel after the event, but was

unable
to unstick it. Decided to pull all cylinders and have the 100 Octane


valves installed. So Marvel at something like $10/gallon, or $2000

to
have the cylinders re-worked. I could buy lots of Marvel for

$2000...

Scott


Dick wrote:
Old WW2 mechanic says he hears a sticky valve on my C-85 when I

fire up for
first time in morning but can't describe the sound and says it

lasts only as
long as a finger snap.

Wants me to add Marvel Mystery oil. I use Aeroshell 100 (50 weight)

and
change it every 25 hours.

I can't detect any roughness upon initial start around 900-1000 rpm

in front
of my hanger nor during the taxi a couple of minutes to a runup

spot. On
throttling up to 1500 for the mag check, I notice a slight

hesitation around
11-1200 rpm that goes away quickly and thought was just from the

low speed
taxi.

Since I had to put a rental down about 7 years ago for a valve

problem (per
the FBO), there is a little "pucker" factor regarding this

conversation G.

Light Plane Maintenance book references "hand proping before first

start of
day to find 'flat' cylinder". Not sure I can identify a rapid

falloff in
turning resistance (books definition).

Concern doesn't seem to get to the point where the "cold cylinder"

test is
applicable as doesn't last long (his finger snap).

Am I chasing nothing or what is a valid approach?

Thanks, Dick



************************************************** ********************************

I have used MMO in my vehicles and tractors and all other internal
combustion equipment for 50+ years and depend on it to help prolong the
life. Will in plane engines also.
Good luck.

Bob Olds RV-4
Charleston,Arkansas


************************************************** *******************************

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Replacing fuel cut-off valve with non-a/c part??? Michael Horowitz Owning 46 January 15th 05 10:20 PM
WTB: ASW 27A water valve Peter Van Camp Soaring 0 April 28th 04 10:37 PM
Stuck valve versus plugged injector Viperdoc Owning 6 April 13th 04 12:15 AM
Q: Disecting a cut-off valve? Michael Horowitz Home Built 0 March 6th 04 01:47 PM
Airplane Parts on Ebay Vac Reg Valves, Fuel Floats, O-200 Spider, Fuel Injection Valve Bill Berle Home Built 0 January 26th 04 07:48 AM


All times are GMT +1. The time now is 05:22 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AviationBanter.
The comments are property of their posters.