Updating FLARM F4/F5 without SD card slot

Op dinsdag 21 mei 2019 16:00:05 UTC+2 schreef Robert Tatlow:
At 11:37 21 May 2019, Senna Van den Bosch wrote:
Hi, I have an older FLARM in my glider and found some issues last weekend
while flying. I'd like to update the firmware but I can't find any
detailed
guide to follow.
So far I have found this guide:
https://support.flarm.com/hc/en-us/a...5694-How-do-I-
update-the-Firmware-on-a-Classic-FLARM-without-an-SD-card-slot-
Only issue I have is how to connect it. I have a serial to USB cable but
the next requirement is "A cable connecting the RS-232 adapter with the
FLARM device"

Does that mean I need a console cable (rs-232 to rj45) as well?
If anyone has some more details on how to connect it, would be greatly
appreciated!


Look up installation manual from Flarm.com for F4/5, flarm without SD
card.

It gives pinouts from RJ 45 and also data pinout to 9 pin Dsub.

So if you use a ready made 8 way cable with a RJ 45 connector each end, cut

one end off open up the cable and separate the individual wires. Use a
meter to
confirm pinouts of power and data from image in manual, power is 12 v, make

sure you have correct polarity, and wire the three wires used for data to 9
pin
Dsub.
Download the flarm tool listed on flarm.com website for updating without SD

card and install on laptop, windows, not apple!
Connect your homemade cable to USB serial adapter and power the flarm.
Choose serial port, may not be the one first offered(1) may be 3.
You may have to go into control panel, device manager, ports and alter
baud
rate. If you get correct port and baud rate you will notice it says connect
to
flarm.

You've mentioned a ready-made cable, would you happen to know where it can be purchased?

At 14:24 21 May 2019, Senna Van den Bosch wrote:
Op dinsdag 21 mei 2019 16:00:05 UTC+2 schreef Robert Tatlow:
At 11:37 21 May 2019, Senna Van den Bosch wrote:
Hi, I have an older FLARM in my glider and found some issues last
weekend
while flying. I'd like to update the firmware but I can't find any
detailed
guide to follow.
So far I have found this guide:
https://support.flarm.com/hc/en-us/a...5694-How-do-I-
update-the-Firmware-on-a-Classic-FLARM-without-an-SD-card-slot-
Only issue I have is how to connect it. I have a serial to USB cable
but
the next requirement is "A cable connecting the RS-232 adapter with
the
FLARM device"

Does that mean I need a console cable (rs-232 to rj45) as well?
If anyone has some more details on how to connect it, would be greatly
appreciated!


Look up installation manual from Flarm.com for F4/5, flarm without SD
card.

It gives pinouts from RJ 45 and also data pinout to 9 pin Dsub.

So if you use a ready made 8 way cable with a RJ 45 connector each end,
cut

one end off open up the cable and separate the individual wires. Use a
meter to
confirm pinouts of power and data from image in manual, power is 12 v,
make

sure you have correct polarity, and wire the three wires used for data
to
9
pin
Dsub.
Download the flarm tool listed on flarm.com website for updating
without
SD

card and install on laptop, windows, not apple!
Connect your homemade cable to USB serial adapter and power the flarm.
Choose serial port, may not be the one first offered(1) may be 3.
You may have to go into control panel, device manager, ports and alter
baud
rate. If you get correct port and baud rate you will notice it says
connect
to
flarm.

You've mentioned a ready-made cable, would you happen to know where it
can
be purchased?

Dickie Feakes at http://www.bas.uk.net/sale.html has them listed

Universal programming lead for Colibri, Swiss Flarm, LX Mini Box, Red Box
etc
with 12v power lead - £15.00

Universal lead as above but with 240v power unit £19.50

Op dinsdag 21 mei 2019 17:45:05 UTC+2 schreef Robert Tatlow:
At 14:24 21 May 2019, Senna Van den Bosch wrote:
Op dinsdag 21 mei 2019 16:00:05 UTC+2 schreef Robert Tatlow:
At 11:37 21 May 2019, Senna Van den Bosch wrote:
Hi, I have an older FLARM in my glider and found some issues last
weekend
while flying. I'd like to update the firmware but I can't find any
detailed
guide to follow.
So far I have found this guide:
https://support.flarm.com/hc/en-us/a...5694-How-do-I-
update-the-Firmware-on-a-Classic-FLARM-without-an-SD-card-slot-
Only issue I have is how to connect it. I have a serial to USB cable
but
the next requirement is "A cable connecting the RS-232 adapter with
the
FLARM device"

Does that mean I need a console cable (rs-232 to rj45) as well?
If anyone has some more details on how to connect it, would be greatly
appreciated!


Look up installation manual from Flarm.com for F4/5, flarm without SD
card.

It gives pinouts from RJ 45 and also data pinout to 9 pin Dsub.

So if you use a ready made 8 way cable with a RJ 45 connector each end,
cut

one end off open up the cable and separate the individual wires. Use a
meter to
confirm pinouts of power and data from image in manual, power is 12 v,
make

sure you have correct polarity, and wire the three wires used for data
to
9
pin
Dsub.
Download the flarm tool listed on flarm.com website for updating
without
SD

card and install on laptop, windows, not apple!
Connect your homemade cable to USB serial adapter and power the flarm.
Choose serial port, may not be the one first offered(1) may be 3.
You may have to go into control panel, device manager, ports and alter
baud
rate. If you get correct port and baud rate you will notice it says
connect
to
flarm.

You've mentioned a ready-made cable, would you happen to know where it
can
be purchased?

Dickie Feakes at http://www.bas.uk.net/sale.html has them listed

Universal programming lead for Colibri, Swiss Flarm, LX Mini Box, Red Box
etc
with 12v power lead - £15.00

Universal lead as above but with 240v power unit £19.50

Just called him, will give it a try. Thank you!