|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
|
|
#1
March 19th 18, 06:13 PM
posted to rec.aviation.soaring
|
|||
|
|||
Piper PA25 Tost tow release conversion
We have run into an issue with the rear most anchoring bolts. The Tost kit as supplied uses AN6 bolts. The existing mounting holes are AN4. Any recommendations?
Thanks, Dan 765 744 4132 
|
|
#2
March 19th 18, 07:56 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Piper PA25 Tost tow release conversion
3/8" drill bit?
|
|
#3
March 19th 18, 08:49 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Piper PA25 Tost tow release conversion
At 19:56 19 March 2018, Tony wrote:
3/8" drill bit? No I think better to sleev tost down to AN4, or contact tost with with the problem. KF
|
|
#4
March 19th 18, 10:34 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Piper PA25 Tost tow release conversion
Sawzall all the things!!!!!
|
|
#5
March 19th 18, 11:01 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Piper PA25 Tost tow release conversion
On Monday, March 19, 2018 at 6:34:24 PM UTC-4, Bob Kuykendall wrote:
Sawzall all the things!!!!! You could be the next youtube sensation....
|
|
#6
March 20th 18, 02:02 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Piper PA25 Tost tow release conversion
On Monday, March 19, 2018 at 1:13:33 PM UTC-5, wrote:
We have run into an issue with the rear most anchoring bolts. The Tost kit as supplied uses AN6 bolts. The existing mounting holes are AN4. Any recommendations? Thanks, Dan 765 744 4132 Daniel, we just finishes installing a Tost CRG winch system in our Pawnee and may be able to help. PM me and lets figure this out. We (SLSA) have Tost winches in both our Pawnees and love them. Kirk kirk dot stant at gmail dot com
|
|
#7
March 20th 18, 09:56 PM
posted to rec.aviation.soaring
|
|||
|
|||
|
Piper PA25 Tost tow release conversion
On Monday, March 19, 2018 at 2:13:33 PM UTC-4, wrote:
We have run into an issue with the rear most anchoring bolts. The Tost kit as supplied uses AN6 bolts. The existing mounting holes are AN4. Any recommendations? Thanks, Dan 765 744 4132 Sleeve it down, do not drill!
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| TOST Release Failure - Two Uncommanded Release's | [email protected] | Soaring | 11 | October 13th 12 10:23 AM |
| PA25 Hutch Conversion Data | [email protected] | Soaring | 0 | October 20th 10 11:43 PM |
| Anyone have a Tost release? | noel.wade | Soaring | 5 | June 10th 10 04:36 AM |
| FS Tost E85 Release | scooter | Soaring | 0 | March 7th 06 02:31 AM |
| FS Tost E85 Release | scooter | Soaring | 0 | November 22nd 05 01:11 AM |
Hybrid Mode
