|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
|
|
#1
January 4th 05, 02:23 PM
|
|||
|
|||
Cable layout ATR600-PC ?
Hello,
Does anyone have details on the cable used to transfer a frequency database from a PC Com port to a filser ATR600 radio? This cable is mentioned in the manual, but the actual wiring diagram seems to be missing.. Thanks, Lars Peder Denmark -- Lars P. Hansen 
|
|
#2
January 4th 05, 02:35 PM
|
|||
|
|||
|
Hello
manual, but the actual wiring diagram seems to be missing.. The wiring can be found in the manual on page 11: http://www.filser.de/handbuch/atr600instmane.pdf It's a standard serial RS232 communication to the PC (RX, TX, Ground) Regards, Ludovic
|
|
#3
January 4th 05, 09:18 PM
|
|||
|
|||
|
Thanks, Ludovic. -Why bother reading manuals in detail when you can get the
info Quickly from RAS :?) Lars Peder -- -- Lars P. Hansen "Ludovic Launer" wrote in message ... Hello manual, but the actual wiring diagram seems to be missing.. The wiring can be found in the manual on page 11: http://www.filser.de/handbuch/atr600instmane.pdf It's a standard serial RS232 communication to the PC (RX, TX, Ground) Regards, Ludovic
|
|
#4
January 5th 05, 03:17 PM
|
|||
|
|||
|
My God...... why did I bother to pack you up with manuals
at all, then? Do read the Flight Manual at least, you lazy Dane! ;-))))) Cheers, Flavio At 00:3/2 05 January 2005, Lars P. Hansen wrote: Thanks, Ludovic. -Why bother reading manuals in detail when you can get the info Quickly from RAS :?) Lars Peder -- -- Lars P. Hansen 'Ludovic Launer' wrote in message ... Hello manual, but the actual wiring diagram seems to be missing.. The wiring can be found in the manual on page 11: http://www.filser.de/handbuch/atr600instmane.pdf It's a standard serial RS232 communication to the PC (RX, TX, Ground) Regards, Ludovic
|
|
#5
January 5th 05, 05:59 PM
|
|||
|
|||
|
Hi Flavio,
Well, I just follow the ancient rule: 1) Don't even think of figuring it out yourself 2) Ask anyone around, incl. r.a.s. 3) If all else fails, read the manual. Don't you do it like that in Italy :?) Greetings, Lars Peder ... Looking sooo much forward to get the DG-600 in the air. "Flavio Formosa" wrote in message ... My God...... why did I bother to pack you up with manuals at all, then? Do read the Flight Manual at least, you lazy Dane! ;-))))) Cheers, Flavio
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Can anyone help, PLEASE - searching for zip-cord (aka: mono-cord, speaker wire, shooting wire, dbl hookup, rainbow cable, ribbon cable) | Striker Cat | Home Built | 6 | October 15th 04 08:51 PM |
| best Winch cable? | yo | Soaring | 2 | April 2nd 04 03:47 PM |
| cable splicing(w/o ferrules) | Andy Davey | Soaring | 2 | March 19th 04 12:49 PM |
| Rudder cable - was The Little Wheel in Back | BD5ER | Home Built | 9 | September 11th 03 04:14 PM |
| Winch cable | Bill Daniels | Soaring | 5 | August 24th 03 11:13 PM |
Hybrid Mode
