![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
To all the 601 builders out there. How long does it actually take to
build the basic kit? I'm not talking about all the extras that are on our dare to dream list, or the quick build kit, I mean basic VFR package, easy paint, just enough to have fun and fly. Lou |
#2
|
|||
|
|||
![]()
Bryan Martin wrote:
A first time builder with some mechanical aptitude could probably get one flying in about 800 to 1000 hours. I got mine flying with about 1200 hours with an IFR panel and polished aluminum finish. In article , Lou wrote: To all the 601 builders out there. How long does it actually take to build the basic kit? I'm not talking about all the extras that are on our dare to dream list, or the quick build kit, I mean basic VFR package, easy paint, just enough to have fun and fly. Lou Not finished yet but from first measurement to first take-off I'd say Bryan's numbers sound about right. I would say though that 2 guys who had done it before who either had ready access to spare parts and/or were able to fab their own could build the air frame in half that time if not less. I've been working on mine since Oct of 2002. The tail, wings and some of the fuselage were built on the patio of my house. I worked mainly on the weekends and made very good time. The tail and wings were done in 2004. I started on the fuselage and then decided that I might as well go ahead and get my hanger built. That put almost a one year hold on any building. Once I got in the hanger the South Arkansas heat limited the amount of time I could spend out there 6 months out of the year then we got to the point where I was waiting about a year to have my engine built. I didn't want to do much of the electrical until I had the engine so that delayed me yet again. Now with the engine on the mount things are once again moving at quite a clip. As I get closer I find myself working during the week on it some as well. |
#3
|
|||
|
|||
![]()
At expo '89' in Vancouver B.C. Chapter 85 members along with Chris Heintz,
two of his teenage boys, his shop foreman and myself who had built a zenith from plans assembled a 601 kit. There were probably an average of 8 workers for 12 hrs a day. 12 days later I test flew it at Boundary Bay. Stew "Lou" wrote in message ... To all the 601 builders out there. How long does it actually take to build the basic kit? I'm not talking about all the extras that are on our dare to dream list, or the quick build kit, I mean basic VFR package, easy paint, just enough to have fun and fly. Lou |
#4
|
|||
|
|||
![]()
Stew Hicks wrote:
At expo '89' in Vancouver B.C. Chapter 85 members along with Chris Heintz, two of his teenage boys, his shop foreman and myself who had built a zenith from plans assembled a 601 kit. There were probably an average of 8 workers for 12 hrs a day. 12 days later I test flew it at Boundary Bay. Stew While a heck of an achievement I don't think the OP will have the same kind of assistance during his build. |
#5
|
|||
|
|||
![]()
On Jul 14, 1:15 pm, Gig 601Xl Builder
wrote: Stew Hicks wrote: At expo '89' in Vancouver B.C. Chapter 85 members along with Chris Heintz, two of his teenage boys, his shop foreman and myself who had built a zenith from plans assembled a 601 kit. There were probably an average of 8 workers for 12 hrs a day. 12 days later I test flew it at Boundary Bay. Stew While a heck of an achievement I don't think the OP will have the same kind of assistance during his build. Although it wasn't what I had in mind, but it does equal out to 1152 hours so I'd have to bet that it's not a bad estimate. Lou |
#6
|
|||
|
|||
![]() "Gig 601Xl Builder" wrote in message m... I would say though that 2 guys who had done it before... Yes, but having "done it before" imparts a huge advantage, an advantage that few (amateur) homebuilders will ever truly see. Back when I was in charge of a shop that did repetitive radio installation in fleets of police cars, we found that the first installation of a group could take several times as long as the last installation. The learning curve can be an amazing thing. Vaughn |
#7
|
|||
|
|||
![]()
Vaughn Simon wrote:
"Gig 601Xl Builder" wrote in message m... I would say though that 2 guys who had done it before... Yes, but having "done it before" imparts a huge advantage, an advantage that few (amateur) homebuilders will ever truly see. Back when I was in charge of a shop that did repetitive radio installation in fleets of police cars, we found that the first installation of a group could take several times as long as the last installation. The learning curve can be an amazing thing. Vaughn Without a doubt. Perfect example. The first wing I built (the left one) took me a solid 3 months of weekends. They right wing took less than half that. Which brings up an interesting question. There is often a complaint that the 601XL plane flys "left heavy." I wonder if this is because we don't build it as well and it isn't quite as good an airfoil as the right. The build manual has the left built first so just about everyone does it that way. |
#8
|
|||
|
|||
![]()
On 2008-07-14, Gig 601Xl Builder wrote:
Which brings up an interesting question. There is often a complaint that the 601XL plane flys "left heavy." I wonder if this is because we don't build it as well and it isn't quite as good an airfoil as the right. The build manual has the left built first so just about everyone does it that way. My Zodiac does that, too. I think it's just the weight of the pilot on the left side. I don't recall that it flew left wing heavy when I had a friend who weighs more than I do in the right seat. -- Jay Maynard, K5ZC http://www.conmicro.com http://jmaynard.livejournal.com http://www.tronguy.net Fairmont, MN (FRM) (Yes, that's me!) AMD Zodiac CH601XLi N55ZC (got it!) |
#9
|
|||
|
|||
![]()
Jay Maynard wrote:
On 2008-07-14, Gig 601Xl Builder wrote: Which brings up an interesting question. There is often a complaint that the 601XL plane flys "left heavy." I wonder if this is because we don't build it as well and it isn't quite as good an airfoil as the right. The build manual has the left built first so just about everyone does it that way. My Zodiac does that, too. I think it's just the weight of the pilot on the left side. I don't recall that it flew left wing heavy when I had a friend who weighs more than I do in the right seat. Tailwind did the same thing - solo. Two up it balanced perfectly. Richard |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
zenith hds/xl | Ted Leon | Home Built | 5 | July 3rd 08 02:16 PM |
Zenith Aircraft | Curt Fennell | Home Built | 11 | June 27th 06 07:40 AM |
Zenith STOL 801 | R.W. Behan | Home Built | 2 | May 24th 06 02:34 PM |
Zenith CH 601 vs. CH 701, better? | DL152279546231 | Home Built | 7 | February 28th 04 06:01 AM |
Zenith CH 300 kit | DougK | Home Built | 1 | February 16th 04 10:40 PM |